The Minimum Cutting Thickness in Milling Process Simulation Analysis

The Minimum Cutting Thickness in Milling Process Simulation Analysis

著者名:

掲載資料名:

High Speed Machining VI : Selected, peer reviewed papers from the 6th International Conference on High Speed Machining (ICHSM 2014), July 24-25, 2014, Harbin, China

シリーズ名:

Materials science forum

シリーズ巻号:

800-801

発行年:

2014

開始ページ:

264

終了ページ:

268

総ページ数:

5

出版情報:

Aedermannsdorf, Switzerland: Trans Tech Publications

ISSN:

02555476

言語:

英語

請求記号:

M23650

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00054266
シリーズID:	PA00000012
会議名:	International Conference on High Speed Machining (ICHSM 2014)
回次:	6th
会議開催地:	Harbin, China
会議開催年:	2014.07.24-2014.07.25
論文注記:	6th International Conference on High Speed Machining (ICHSM 2014), July 24-25, 2014, Harbin, China

類似資料:

1 国際会議録 Simulation Studies of the Cutting Process on SiCp/Al Composites with Different Volume Fraction of Reinforced SiC Particles B.B. Wang, L.J. Xie, X.B. Wang, X.L. Chen Trans Tech Publications	7 国際会議録 Expert System of the Parameter Optimization in the Heavy-Duty Cutting Processing Y.Q. Chen, Z.J. Li, D.H. Zhu, Z.B. Wang, J.X. Guo Trans Tech Publications
2 国際会議録 Geometry Optimization of D-Type Micro End-Mill with FEM Analysis X.H. Zheng, C.Y. Wang, X.B. Wang, Z.W. Xu, M. Chen Trans Tech Publications	8 国際会議録 The Optimization of Cutting Parameters for Surface Roughness in High Speed Milling Based on Taguchi Method P.N. Li, M. Chen, X.J. Kang, L.N. Zhang, M. Zhou Trans Tech Publications
3 国際会議録 Distortion Simulation of Unsymmetrical Composite Laminates Using the Finite Element Analysis Method M. Li, B.Y. Zhang, X.B. Chen Trans Tech Publications	9 国際会議録 Cutting Parameters Optimization Based on Cutting Force Spectrum when Ball Milling A880 Gas Turbine Blade Profiles X.D. He, C.D. Wang, Z.K. Wang, M. Chen Trans Tech Publications
4 国際会議録 Cutting Force and Tool Wear in Face Milling of Hardened Steel X.B. Cui, J. Zhao Trans Tech Publications	10 国際会議録 The Wear of Al₂O₃-Based Ceramic Cutting Tool in High-Speed Face Milling of AISI H13 Steel Y.H. Zhou, J. Zhao, X.B. Cui Trans Tech Publications
5 国際会議録 Effects of High-Energy Ball Milling Time on the Sintering Process of FeSe Superconductors S.N. Zhang, X.B. Ma, J.X. Liu, J.Q. Feng, C.S. Li Trans Tech Publications	11 国際会議録 Orthogonal Variable Thickness Cutting Modeling of Surface Milling and Physical Fields Simulation W. Zhang, C.J. Du, X.L. Cheng, F.S. He Trans Tech Publications
6 国際会議録 The Design of Ultra-Hard Micro Milling Tool Supplemented to LiF Crystal by Finite Element Analysis Y.Q. Guo, D. Li, M.J. Chen, N. Chen Trans Tech Publications	12 国際会議録 Research on the Modeling and Experimenting of Burr Formation Process in Double-Edged Micro-Plat End Milling Operation N. Chen, M.J. Chen, H.B. Ni, N. He, Z.Q. Liu Trans Tech Publications

1

2

3

4

5

6

7

8

9

10

11

12