Blank Cover Image

Computer Aided Engineering Design of Powder Injection Molding Process for a Dental Scaler Tip Mold Design

著者名:
掲載資料名:
Progress in powder metallurgy : proceedings of the 2006 Powder Metallurgy World Congress & Exhibition (PM 2006), held in Busan Exhibition & Convention Center (BEXCO), Busan, Korea, September 24-28, 2006
シリーズ名:
Materials science forum
シリーズ巻号:
534-536
発行年:
2007
パート:
1
開始ページ:
341
終了ページ:
344
総ページ数:
4
出版情報:
Aedermannsdorf, Switzerland: Trans Tech Publications
ISSN:
02555476
ISBN:
9780878494194 [0878494197]
言語:
英語
請求記号:
M23650
資料種別:
国際会議録

類似資料:

1 国際会議録 Development of Dental Scaler Tip Mold with Powder Injection Molding Process

C.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung, B.O. Rhee

Trans Tech Publications
7 国際会議録 COMPUTER-AIDED ENGINEERING (CAE) FOR INJECTION MOLDING OF PLASTICS

Wang, K. K.

American Institute of Chemical Engineers
2 テクニカルペーパー Computer-Aided Design and Fabrication of Molds and Computer Control of Injection Molding

Wang,K.K., Shen,S.F., Hieber,C.A., Isayev,A.I., Cohen,C.

Society of Automotive Engineering, Inc.
8 国際会議録 Computer-Aided Dental Implant Technology

Ting, Yu, Huang, Ta Ko

Trans Tech Publications
3 国際会議録 Three-Dimensional Computer-Aided Mold Cooling Design for Injection Molding

Chang, R.Y., Hsu, D.C., Yang, V., Yang, W.H.

Society of Plastics Engineers
9 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
4 国際会議録 Computer-Aided Cooling-system Design for Injection Molding

Kwon H. T., Wang K. K.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
5 国際会議録 Computer-Aided-Engineering for the Gas-Assisted Injection Molding Process

Turng, L. S.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
6 国際会議録 A Numerical Virtual Process Modeler Based on Computer Aided Engineering Software for Injection Molding

Wang, P. J., Liang, J. M.

Society of Plastics Engineers, Inc. (SPE)
12 国際会議録 Computer aided analysis in plastics injection mold and part design

Rechards, D. A., Thomas, P. M., McDonald, D. L.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12