Surface Integrity of H13 ESR Mould Steel Milled by Carbide and CBN Tools

Surface Integrity of H13 ESR Mould Steel Milled by Carbide and CBN Tools

著者名:

掲載資料名:

Advanced materials forum III : proceedings of the III International Materials Symposium Materiais 2005 and XII Encontro da Sociedade Portuguesa de Materiais - SPM Universidade de Aveiro, March 20-23, Aveiro, Portugal, 2005

シリーズ名:

Materials science forum

シリーズ巻号:

514-516

発行年:

2006

パート:

1

開始ページ:

564

終了ページ:

568

総ページ数:

5

出版情報:

Uetikon-Zuerich, Switzerland: Trans Tech Publications

ISSN:

02555476

ISBN:

9780878494026 [0878494022]

言語:

英語

請求記号:

M23650

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00015823
シリーズID:	PA00000012
会議名:	International Materials Symposium ; Encontro da Sociedade Portuguesa de Materiais (SPM)
回次:	2005 : 3rd ; 12th
会議開催地:	Aveiro, Portugal
会議開催年:	2005.03.20-2005.03.23

類似資料:

1 国際会議録 Experimental and FEM Analysis of Cutting Sequence on Residual Stresses in Machined Layers of AISI 316L Steel Outeiro, J.C., Umbrello, D., M'Saoubi, R. Trans Tech Publications	7 テクニカルペーパー Comparison of Surface Roughness and residual Stresses Induced by Coated Carbide, Ceramic and CBN Cutting Tools in High Speed Facing of Inconel 718 Arunachalam, R.M., Spowage, A.C., Mannan, M.A. Society of Manufacturing Engineers
2 国際会議録 Influence of Work Material Properties on Residual Stresses and Work Hardening Induced by Machining Outeiro, J.C.., Dias, A.M Trans Tech Publications	8 国際会議録 Indium gallium arsenide photodiode arrays for optical communications Cohen,M.J., Brubaker,R.M., Dries,J.C., Ettenberg,M.H. SPIE-The International Society for Optical Engineering
3 テクニカルペーパー Role of Cutting Parameters and Microstructure on Chip Formation and Surface Integrity During Machining of AISI 316L M'SAOUBI RACHID, CHANDRASEKARAN H. Society of Manufacturing Engineers	9 国際会議録 Forecast of Limit Cutting Depth for Hardened Mould Steel Milling X.L. Liu, J. Ma, C.X. Yue, R.Y. Li, A.S. Zhang Trans Tech Publications
4 国際会議録 Tool Wear and Surface Integrity in High Speed Milling of Forging and Cast TA15 Alloys with Coated Carbide Tools P. Liu, J.H. Xu, Y.C. Fu Trans Tech Publications	10 国際会議録 Degradation and Viscoelastic Properties of PLA-PCL, PGA-PCL, PDO and PGA Fibres A.C. Vieira, J.C. Vieira, R.M. Guedes, A.T. Marques Trans Tech Publications
5 国際会議録 Analysis of Microscopic Damage of Hardened Steel Milling Surface on Mould Service Process W. Zhang, J.H. Xu, M.L. Zheng, H.L. Liu, T. Wu Trans Tech Publications	11 国際会議録 Investigation on Performance of a CVD Coated Carbide Tool in Face Milling of Ultra-High Strength Steel 30Cr3SiNiMoVA J.B. Song, C.Y. Wang, L. Zan, M. Chen Trans Tech Publications
6 国際会議録 The Impact of Hardened Steel Milling Surface Structure on Mould Service Load M.L. Zheng, J.H. Xu, W. Zhang, Z.X. Zhang, T. Wu Trans Tech Publications	12 国際会議録 Study on Surface Integrity in Hard Milling of Hardened Die Steel L.L. Jing, G. Liu, M. Chen Trans Tech Publications

1

2

3

4

5

6

7

8

9

10

11

12