Validation of Shrinkage Predications for Injection Molded Parts

Validation of Shrinkage Predications for Injection Molded Parts

著者名:

Prasad, S. ( University of Massachusetts Lowell )
Sharma, S. ( University of Massachusetts Lowell )
Jariwala, M. ( University of Massachusetts Lowell )
Barry, C.M.F. ( University of Massachusetts Lowell )

掲載資料名:

ANTEC 2004, 62nd annual technical conference, Chicago, IL, May 16-20, 2004

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

62

発行年:

2004

開始ページ:

2670

終了ページ:

2673

総ページ数:

4

出版情報:

Brookfield Center, Conn.: Society of Plastics Engineers

ISBN:

9780975370704 [0975370707]

言語:

英語

請求記号:

S42700/62-2

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00013190
シリーズID:	PA00000030
会議名:	ANTEC : Annual Technical Conference
回次:	2004 : 62nd
会議開催地:	Chicago, IL, USA
会議開催年:	2004.05.16-2004.05.20

類似資料:

1 国際会議録 Validation of Shrinkage Predictions for Injection Molded Parts Prasad, S.H., Jariwala, M., Sharma, S.S., Barry, C.F., Malur, V. Society of Plastics Engineers	7 国際会議録 Linear Shrinkage Differences in Plastic Injection Molded Parts Velarde, D. A., Yeagley, M. J. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Criteria for Flow Instabilities in End-Gated Injection Molds Jain, N. S., Barry, C. M. F. Society of Plastics Engineers	8 国際会議録 Shrinkage Analysis of Reinforced Injection Molded Parts Sanschagrin B., Rivard S., Hebert P. L., Girard P. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Post-Filling Simulation and Analyses of Shrinkage and Warpage of the Injection Molded Parts Chen, S. -C., Jeng, K. -K. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Evaluating Factors Affecting Shrinkage Predictions Sharma, S.S., Nirkhe, C.P., Barry, C.M. Society of Plastics Engineers
4 国際会議録 Shrinkage Analysis of Injection Molded polypropylene Parts Mamat, A., Trochu, F., Sanschagrin, B. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Injection Moldability of Crosslinked Polyethylene Mehta, V. A., Barry, C. M. F., Schott, N. R. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Studies on the Influence of the Holding Pressure on the Orientation and Shrinkage of Injection Molded Parts (98) Pontes,A.J., Oliveira,M.J., Pouzada,A.S. Society of Plastic Engineers.	11 国際会議録 Experimental Verification of Simulating Shrinkage and Warpage of Thin Compression Molded SMC Parts Osswald, T. A., Sun, E. M., Tseng, S. -C., Gramann, P. J. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Linear Shrinkage Differences in Plastic Injection Molded Parts Velarde, D. A., Yeagley, M. J. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Shrinkage Analysis of Molded Parts Using Neural Network Lee C. S., Baek H. J., Youn R. J. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12