Blank Cover Image

Microcellular Injection Molding

著者名:
Turng, L-S.T. ( University of Wisconsin-Madison )  
掲載資料名:
ANTEC 2003, annual technical conference, May 4-8, Nashville, Tennessee
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
61
発行年:
2003
開始ページ:
686
終了ページ:
690
総ページ数:
5
出版情報:
Brookfield Center, Conn.: Society of Plastics Engineers
ISBN:
9780972718011 [097271801X]
言語:
英語
請求記号:
S42700/61-1
資料種別:
国際会議録

類似資料:

1 国際会議録 Modeling Cell Nucleation During Microcellular Injection Molding

Hernandez, J.P., Chandra, A., Winardi, A., Osswald, T.A., Turng, L-S.T., Gramann, P.

Society of Plastics Engineers
7 国際会議録 A Web-Based Knowledge Management System for the Injection Molding Process

Turng, L. -S., DeAugistine, D.

Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Application of Polyamide/Cellulose Fiber/Wollastonite Composites for Microcellular Injection Molding

Winata, H., Turng, L-S.T., Caulfield, D.F., Kuster, T., Spindler, R., Jacobson, R.E.

Society of Plastics Engineers
8 国際会議録 Development of an Integrated Computer-Aided Engineering and Optimization System for Injection Molding (660)

Peic,M., Turng,L-S.

Society of Plastic Engineers.
3 国際会議録 Microcelluar Nnocomposite Injection Molding Process

Yuan, M., Turng, L-S.T., Spindler, R., Caulfield, D.F., Hunt, C.

Society of Plastics Engineers
9 国際会議録 Optimization Strategies for Injection Molding

Turng S. L., Chiang H. H., Stevenson F. J.

Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Simulation of Co-Injection and Gas-Assisted Injection Molding

Turng, L. S.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Microcellular Injection Molding of Polylactide and Polylactide-Montmorillonite Nanocomposites

Shaoqin (Sarah) Gong, Lih-Sheng Turng, Adam Kramschuster, Tao Li

American Institute of Chemical Engineers
5 国際会議録 Computer-Aided-Engineering for the Gas-Assisted Injection Molding Process

Turng, L. S.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Study of Weld-Line Strength and Microstructure of Injection Molded Microcellular Parts (1020)

Kharbas,H., Turng,L-S., Spindler,R., Burhop,B.

Society of Plastic Engineers.
6 国際会議録 New Developments in CAET Technology for the Gas-Assisted Injection Molding Process

Turng S. L.

Society of Plastics Engineers, Inc. (SPE)
12 国際会議録 General Design Guidelines for Gas-Assisted Injection Molding Using a CAE Tool

Barton, K. S., Turng, L. S.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12