Frozen Layer Effect on Measuring the Internal Cavity Pressure During Injection Molding

Frozen Layer Effect on Measuring the Internal Cavity Pressure During Injection Molding

著者名:

Shin, J-W. ( The University of Akron )
Lee, H-S. ( Chungju National University )
Isayev, A.I. ( The University of Akron )

掲載資料名:

ANTEC 2003, annual technical conference, May 4-8, Nashville, Tennessee

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

61

発行年:

2003

開始ページ:

561

終了ページ:

565

総ページ数:

5

出版情報:

Brookfield Center, Conn.: Society of Plastics Engineers

ISBN:

9780972718011 [097271801X]

言語:

英語

請求記号:

S42700/61-1

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00012896
シリーズID:	PA00000030
会議名:	ANTEC : Annual Technical Conference
回次:	2003 : 61st
会議開催地:	Nashville, TN, USA
会議開催年:	2003.05.04-2003.05.08
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 Transient Gas/Melt Interface and Gas Penetration During Gas-Assisted Injection Molding: Simulation and Experiment Li, C., Shin, J-W., Isayev, A.I., Lee, H-S. Society of Plastics Engineers	7 国際会議録 The Effect of Varying Injection Molding Conditions on Cavity Pressure Macfarlane, S., Dubay, R. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Effect of Injection Speed on Gas Penetration Length, Residual Wall Thickness and the Melt Front Position During Gas-Assisted Injection Molding Shin, J-W., Isayev, A.I. Society of Plastics Engineers	8 国際会議録 The Effect of Internal Cooling on Fingering in the Gas-Assisted Injection Molding (616) Lee,J.S., Cha,S., Lai,F. Society of Plastic Engineers.
3 国際会議録 Experimental Study of Gas Penetration in the Gas-Assisted Injection Molding (174) Shin,J-W., Isayev,A.I. Society of Plastic Engineers.	9 国際会議録 Simultaneous Sandwich Injection Molding: Simulation and Experiment Lee J. D., Isayev I., White L. J. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Effect of processing conditions on crystallinity and microstructure of injection moldings of polypropylenes of various molecular weights Demiray, M., Isayev, A.I. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Cavity-Pressure Variations During the Post-Filling Stage of Injection Molding Hieber A. C., Vandenengel G., Chiang H. H. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 The Comparison of Newly Proposed Cavity-Variable-Based Full Factorial Design and Artificial Neural Network in Injection Molding Process Kim, J. G., Shin, I. H., Lee, J. W. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Cavity Pressure Control in Injection Molding During Filling, Packing, and Holding Fara, D. A., Patterson, W. I., Kamal, M. R. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Orientation development in the injection molding of amorphous polymers Isayev, A. I. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Study of Cavity Pressure and its Prediction During Injection Molding Xu, G., Koelling, K.W. Society of Plastics Engineers

1

2

3

4

5

6

7

8

9

10

11

12