Transient Gas/Melt Interface and Gas Penetration During Gas-Assisted Injection Molding: Simulation and Experiment

Transient Gas/Melt Interface and Gas Penetration During Gas-Assisted Injection Molding: Simulation and Experiment

著者名:

Li, C. ( The University of Akron )
Shin, J-W.
Isayev, A.I.
Lee, H-S. ( Chungju National University )

掲載資料名:

ANTEC 2003, annual technical conference, May 4-8, Nashville, Tennessee

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

61

発行年:

2003

開始ページ:

414

終了ページ:

418

総ページ数:

5

出版情報:

Brookfield Center, Conn.: Society of Plastics Engineers

ISBN:

9780972718011 [097271801X]

言語:

英語

請求記号:

S42700/61-1

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00012896
シリーズID:	PA00000030
会議名:	ANTEC : Annual Technical Conference
回次:	2003 : 61st
会議開催地:	Nashville, TN, USA
会議開催年:	2003.05.04-2003.05.08
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 Effect of Injection Speed on Gas Penetration Length, Residual Wall Thickness and the Melt Front Position During Gas-Assisted Injection Molding Shin, J-W., Isayev, A.I. Society of Plastics Engineers	7 国際会議録 Applications of Gas-Assisted Injection Molding and Injection/Compression Molding in Thinwall Molding Wang, T. J., Chen, S. -C., Chiang, H. H. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Experimental Study of Gas Penetration in the Gas-Assisted Injection Molding (174) Shin,J-W., Isayev,A.I. Society of Plastic Engineers.	8 国際会議録 The Investigation of Flow Behavior of Polymeric Melts in the Water Assisted Injection Molding Chang, R.Y., Huang, C.T., Yang, W.H., Tsai, M.H., Lu, K.I., Liu, S.J. Society of Plastics Engineers
3 国際会議録 Frozen Layer Effect on Measuring the Internal Cavity Pressure During Injection Molding Shin, J-W., Lee, H-S., Isayev, A.I. Society of Plastics Engineers	9 国際会議録 Gas Assisted Injection Molding of a Vacuum Cleaner Body Rhee, B. O., Ahn, H. -K., Lee, K. D., Yu, B. K., Son, C. -W. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Interface and Encapsulation in Simultaneous Co-Injection Molding of Disk: Two-Dimensional Simulation and Experiment (249) Li,C.T., Isayev,A.I. Society of Plastic Engineers.	10 国際会議録 Flow Directions in the Gas Assisted Injection Molding Technology Soh S. Y., Chung H. C. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Simultaneous Sandwich Injection Molding: Simulation and Experiment Lee J. D., Isayev I., White L. J. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Investigation of Thermal Conduction between Mold and Melt during Injection Molding Process Liao, M. K., Li, C. S. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Simulation and Experimental Studies of a Non-Return Valve Performance during Injection Molding Zook, C., Isayev, A. I. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Statistical Experiment Study of Gas-Assisted Injection Molding Process Zhao J., Lu X., Fong L., Chiang H. H. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12