Blank Cover Image

Interface and Encapsulation in Simultaneous Co-Injection Molding of Disk: Two-Dimensional Simulation and Experiment (249)

著者名:
  • Li,C.T. ( Institute of Polymer Enineering, The University of Akron, Akron, OH 44325-0301 )
  • Isayev,A.I.
掲載資料名:
ANTEC 2002, annual technical conference, San Francisco, CA, May 5-9, 2002
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
60
発行年:
2002
巻:
1
開始ページ:
465
終了ページ:
469
総ページ数:
5
出版情報:
Brookfield, Conn.: Society of Plastic Engineers.
ISBN:
9780971643505 [0971643504]
言語:
英語
請求記号:
S42700/60
資料種別:
国際会議録

類似資料:

1 国際会議録 Transient Gas/Melt Interface and Gas Penetration During Gas-Assisted Injection Molding: Simulation and Experiment

Li, C., Shin, J-W., Isayev, A.I., Lee, H-S.

Society of Plastics Engineers
7 国際会議録 Effect of processing conditions on crystallinity and microstructure of injection moldings of polypropylenes of various molecular weights

Demiray, M., Isayev, A.I.

Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Simultaneous Sandwich Injection Molding: Simulation and Experiment

Lee J. D., Isayev I., White L. J.

Society of Plastics Engineers, Inc. (SPE)
8 国際会議録 Experimental Study of Gas Penetration in the Gas-Assisted Injection Molding (174)

Shin,J-W., Isayev,A.I.

Society of Plastic Engineers.
3 国際会議録 Two-Dimensional Viscoelastic Simulation of Injection Molding of Thermoplastic Materials

Sobhanie M., Isayev I. A.

Society of Plastics Engineers, Inc. (SPE)
9 国際会議録 Volumetric Effects in the Injection Molding of Polymers

Isayev I. A., Hariharan T.

Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Simulation and Experimental Studies of a Non-Return Valve Performance during Injection Molding

Zook, C., Isayev, A. I.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Effect of Injection Speed on Gas Penetration Length, Residual Wall Thickness and the Melt Front Position During Gas-Assisted Injection Molding

Shin, J-W., Isayev, A.I.

Society of Plastics Engineers
5 国際会議録 Orientation development in the injection molding of amorphous polymers

Isayev, A. I.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Multi-Component Injection Molding-Part 1: Interface and Microstructure Development

Palluch, K. P., Isayev, A. I.

Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Microstructure of Injection Molding of Isolactic Polypropylenes with Various Molecular Weights: Simulation and Experiment

Isayev I. A., Guo X., Guo L., Demiray M.

Society of Plastics Engineers, Inc. (SPE)
12 国際会議録 Flow-Induced Crystallization and Birefringence in Injection Molding of Semicrystalline Polymers

Kim, K., Isayev, A.I., Kwon, K.

Society of Plastics Engineers
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12