Blank Cover Image

The Comparison of Newly Proposed Cavity-Variable-Based Full Factorial Design and Artificial Neural Network in Injection Molding Process

著者名:
掲載資料名:
ANTEC 2000 Conference proceedings, May 7-11, 2000, Orlando, Florida
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
46
発行年:
2000
パート:
1
開始ページ:
601
終了ページ:
605
総ページ数:
5
出版情報:
Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)
ISBN:
9781566768559 [1566768551]
言語:
英語
請求記号:
S42700/46
資料種別:
国際会議録

類似資料:

1 国際会議録 The Part Quality Prediction from Ultrasonic Wave and Artificial Neural Network in Injection Molding Process (581)

Kim,J.G., Lee,J.W.

Society of Plastic Engineers.
7 国際会議録 In Situ Measurement of Process Stream Temperatures within a Variable Depth Cavity during the Injection Molding Cycle

Rietveld, J. X., Lai, G. -Y.

Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Frozen Layer Effect on Measuring the Internal Cavity Pressure During Injection Molding

Shin, J-W., Lee, H-S., Isayev, A.I.

Society of Plastics Engineers
8 国際会議録 Prediction of Injection Molded Plaque Properties Using Artificial Neural Networks and Flow Simulation

Kim H. B., Hwang W. T., Farooqi S., Witkus S.

Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Predicting conversion time of circuit design file by artificial neural networks

S.-H. Jang, J.-H. Lee, B.-S. Ahn, W.-T. Ki, J.-H. Choi

Society of Photo-optical Instrumentation Engineers
9 国際会議録 Numerical Analysis of Injection/Compression Molding Process for Center-Gated Disc

Park J. S., Han H. J., Ryim G. W., Chang K. S., Kim H. J., Kang G. T., Heo S. B., Kwon H. T.

Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Quality control in injection molding with an adaptiv process model based on neural networks

Haussler, J., Wortberg, J.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Transient Gas/Melt Interface and Gas Penetration During Gas-Assisted Injection Molding: Simulation and Experiment

Li, C., Shin, J-W., Isayev, A.I., Lee, H-S.

Society of Plastics Engineers
5 国際会議録 Study of the Influence of the Injection Molding Processing Parameters on Molded Part Properties Using the Full Factorial Design

Rujnic-Sokele, M., Catic, I.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Application of Artificial Neural Networks to Optimize Processing - Properties of Ni-Tic Composite Coatings

H.J. Wei, W.C. Sun, G.Q. Hou, F. Zhang, Q. Shi

Trans Tech Publications
6 国際会議録 Design of a sliding mode control scheme using neural networks

Lee,D.-W., Cho,J.-H., Kim,Y.T.

SPIE-The International Society for Optical Engineering
12 国際会議録 Unified Design Method of the Cavity for Injection Molded Spur Gears

Lee, S. -C., Kim, C. -H., Kwon, O. -K., Huh, Y. -J.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12