Optimum Design of Process Conditions to Minimize Residual Stresses in Injection-Molded Parts

Optimum Design of Process Conditions to Minimize Residual Stresses in Injection-Molded Parts

著者名:

Kang S. ( Cornell University )
Hieber A. C. ( Cornell University )
Wang K. K. ( Cornell University )

掲載資料名:

ANTEC 95, Boston, May 7-11, Boston : The plastics challenge - a revolution in education : Volume I. Processing

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

41(1)

発行年:

1995

巻:

1

開始ページ:

991

終了ページ:

996

総ページ数:

6

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566763196 [1566763193]

言語:

英語

請求記号:

S42700/962601

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00020153
シリーズID:	PA00000030
会議名:	ANTEC '95 :: Annual Technical Conference
回次:	53rd
会議開催地:	Boston, MA, USA
会議開催年:	1995.05.07-1995.05.11
論文注記:	MOLD MAKING & MOLD DESIGN DIVISION

類似資料:

1 国際会議録 Mold-Filling-Simulation in Injection Molding of Three-Dimensional Thin Parts Wang W. V., Hieber A. C., Wang K. K. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Effect of processing conditions on the residual stresses in the injection molding of amorphous polymers Crouthamel, D. L., Isayev, A. I., Wang, K. K. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 The Effects of Boundary Conditions on the Dimensional Changes and Residual Stresses in Injection-Molded Polycarbonate Parts Bushko C. W., Stokes K. V. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Birefrengent Residual Stress and Improved Injection Mold Design J.C. Hanan Trans Tech Publications
3 国際会議録 Optimal Mold Design Methodology to Minimize Warpatge in Injection Molded Parts Sahu R., Yao D., Kim B. Society of Plastics Engineers, Inc. (SPE)	9 テクニカルペーパー Computer-Aided Design and Fabrication of Molds and Computer Control of Injection Molding Wang,K.K., Shen,S.F., Hieber,C.A., Isayev,A.I., Cohen,C. Society of Automotive Engineering, Inc.
4 国際会議録 AN INTERACTIVE COMPUTER PROGRAM FOR RUNNER-SYSTEM DESIGN IN INJECTION MOLDING Wang, V. W., Wang, K. K., Hieber, C. A. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 The Effects of Processing Conditions on the Pressure Losses in a Runner-Gate-Cavity System Hieber A. C., Wang W. V., Wang K. K., Chung B. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Structure Performance of Thin-Wall Injection Molded Parts Chen, S. C., Jong, W. R., Chang, Y. P., Kang, Y., Peng, H. S., Huang, L. T., Ynag, L. K., Chang, C. T., Luo, R. C. Society of Plastics Engineers	11 国際会議録 Injection Molding a Center-Gated Disk: Modelling and Measurements for the Filling and Post-Filling Stages Including Gapwise Shrinkage Hieber, C. A., Wang, K. K. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Computer-Aided Design Software for Cooling System in Injection Molding Himasekhar K., Hieber A. C., Wang K. K. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Minimizing Residual Streses in Molded Parts Liou, M., Suh, N. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12