An Analysis of Pre-Consumer Regrind in an Injection Molded Thermoplastic Part

An Analysis of Pre-Consumer Regrind in an Injection Molded Thermoplastic Part

著者名:

Scriven T. ( Western Washington University )
Sykes S. ( Western Washington University )

掲載資料名:

ANTEC 95, Boston, May 7-11, Boston : The plastics challenge - a revolution in education : Volume I. Processing

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

41(1)

発行年:

1995

巻:

1

開始ページ:

348

終了ページ:

350

総ページ数:

3

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566763196 [1566763193]

言語:

英語

請求記号:

S42700/962601

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00020153
シリーズID:	PA00000030
会議名:	ANTEC '95 :: Annual Technical Conference
回次:	53rd
会議開催地:	Boston, MA, USA
会議開催年:	1995.05.07-1995.05.11
論文注記:	EXTRUSION DIVISION

類似資料:

1 国際会議録 Non-Ferrous Metal Separator Applications in Pre- and Post-Consumer Thermoplastic Regrind Groth B., Mravic M., Schott N. R., Shah D., Rahman M. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Design and Analysis of an Injection Mold to Study Flow of High Performance Thermoplastics in Thin Channels Griffing S. J., Manson E. -A. J., Seferis C. J., Postel L. S. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Injection Molded Engineering Thermoplastics: A Critical Evaluation of Processability and Part Dimensional Stability Efner, H., Largent, T., Allen, D., Lee, D. M. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 CAE Application: Shrinkage and Warpage of an Injection Molded Part Wu S. S. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Compatibility of Adhesives with Thermoplastic Regrind Sivy, G. T. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Part Weight Control in Thermoplastic Injection Molding Operations Srinivasan, K., Srinivasan, T., Maul, G. P. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Residual Stresses in Injection Molded Thermoplastics Vincent, M., Giroud, T. Trans Tech Publications	10 国際会議録 Application of Scanning Acoustic Microscopy to Injection Molded Semi-Crystalline Thermoplastics Kuriyama T., Narisaw I., Abe T. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Functional Feature-Based Approximate Structural Analysis for Injection Molded LFRTP Part Xu, T., Chassapis, C. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Application of Scanning Acoustic Microscopy to Injection Molded Semi-Crystalline Thermoplastics Kuriyama T., Narisawa I., Abe T. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Minimizing Warpage of Injection Molded part by Systematical Simulation Analysis Ni, S.S. Society of Plastics Engineers	12 国際会議録 Characterization and Moldability Analysis of Epoxy Reaction Injection Molding Resins Osinski, J. S., Manzione, L. T. American Chemical Society

1

2

3

4

5

6

7

8

9

10

11

12