Numerical Simulations of Mold Filling for Design and Control of RTM Process

Numerical Simulations of Mold Filling for Design and Control of RTM Process

著者名:

Simacek P. ( University of Delaware )
Sozer M. E. ( University of Delaware )
Advani G. S. ( University of Delaware )

掲載資料名:

Conference proceedings at ANTEC '98 : plastics on my mind, Society of Plastics Engineers, Atlanta, Georgia, April 26-April 30, 1998

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

44(2)

発行年:

1998

巻:

2

開始ページ:

2327

終了ページ:

2335

総ページ数:

9

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566766692 [1566766699]

言語:

英語

請求記号:

S42700/44-2

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018761
シリーズID:	PA00000030
会議名:	ANTEC '98 : Annual Technical Conference
回次:	56th
会議開催地:	Atlanta, GA, USA
会議開催年:	1998.04.26-1998.04.30
論文注記:	COMPOSITES DIVISION

類似資料:

1 国際会議録 Estimating Permeability of Compacted Fabrics and Its Use in Modeling and Control of the RTM Process Sozer, E. M., Gokce, A., Advani, S. G. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 An Approach to Couple Mold Design and On-line Control to Manufacture Complex Composite Parts by Resin Trasfer Molding Lawrence, J.M., Advani, S.G., Devillard, M. Society of Plastics Engineers
2 国際会議録 A Numerical Simulation of the Resin Transfer Mold Filling Process Bruschke V. M., Advani G. S. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Numerical Simulation of Die-Casting Mold Filling Process by Using Fractional Step Method J. Yang, Y.X. Ren, S.M. Xiong Trans Tech Publications
3 国際会議録 Important Mold Filling Issues in Liquid Composite Molding Processes: Modeling and Experiments Bickerton S., Simacek P., Pillai M. K., Mogavero J., Advani G. S. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Numerical Simulation of the Sequential Filling in Injection Molding Process Gao, D. M., Nguyen, K. T., Girard, P., Salloum, G. Society of Plastics Engineers, Inc. (SPE)
4 テクニカルペーパー Use of sensors and simulations for strategic control of liquid composite mold filling process Sozer, E. Murat, Advani, Suresh G., Bickerton, Simon Society of Manufacturing Engineers	10 国際会議録 Predicting the effect of preforming on RTM mold filling Bakharev, Alexander S., Tucker, Charles L., III Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 A Numerical Study of Bubble Growth During Low Pressure Structural Foam Mold Filling Process Arefmanesh A., Advani G. S., Michaelides E. E. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Resin Infusion Process Simulation (RIPS): A Fast Method for Three Dimensional Geometries Gallez E. X., Advani G. S. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 RTM Simulation: Non-Isothermal Flow and Cure Kinetics for Complex 3-D Shell-Like Structures Bruschke V. M., Advani G. S. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Transient Numerical Simulation of Non-Isothermal Process of RTM M. R. Shahnazari, A. Abbassi American Society of Mechanical Engineers

1

2

3

4

5

6

7

8

9

10

11

12