Blank Cover Image

Investigation of Thermal Conduction between Mold and Melt during Injection Molding Process

著者名:
掲載資料名:
ANTEC 94 : plastics : gateway to the future : conference proceedings, San Francisco May 1-5 1994 : Volume I. Processing
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
40(1)
発行年:
1994
巻:
1
開始ページ:
501
終了ページ:
505
総ページ数:
5
出版情報:
Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)
言語:
英語
請求記号:
S42700/941468
資料種別:
国際会議録

類似資料:

1 国際会議録 Investigation on Thermal Debinding of Powder Injection Molding

Lam, Y.C., Shengjie, Y., Lam, K.H., Ma, J., Tam, K.C., Yu, S.C.M.

Trans Tech Publications
7 国際会議録 Experimental Investigation of Thermal Contact Resistance in Injection Molding

Rhee, B. O., Hieber, C. A., Wang, K. K.

Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 The Investigation of Flow Behavior of Polymeric Melts in the Water Assisted Injection Molding

Chang, R.Y., Huang, C.T., Yang, W.H., Tsai, M.H., Lu, K.I., Liu, S.J.

Society of Plastics Engineers
8 国際会議録 Comparing Ultrasonic and Cavity Pressure Sensors for In-the-mold Process Monitoring in Injection Molding

Baek, S. Y., Edwards, R., Thomas, C. L., Peterson, R.

Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Heat Transfer Measurement at the Mold Surface During Injection Molding of Thermoplastic Melts

Kamal, M. R., Salloum, G., Garcia-Rejon, A.

Society of Plastics Engineers, Inc. (SPE)
9 国際会議録 Development of Dental Scaler Tip Mold with Powder Injection Molding Process

C.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung, B.O. Rhee

Trans Tech Publications
4 国際会議録 Study of Polymer Melt Flow during Injection Molding Using Co-Injection Molding Technique

Chen, S. C., Hsu, K. F., Jung, W. R.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Investigation of Injection Molding Process Robustness for Various Molding Strategies (1199)

Albertson,A.S., Brendel,M.V.

Society of Plastic Engineers.
5 国際会議録 Transient Gas/Melt Interface and Gas Penetration During Gas-Assisted Injection Molding: Simulation and Experiment

Li, C., Shin, J-W., Isayev, A.I., Lee, H-S.

Society of Plastics Engineers
11 国際会議録 Micro Assembly Injection Molding-Mold and Processing Technology

Ziegmann, C., Michaeli, W.

Society of Plastics Engineers
6 国際会議録 Investigation of Optimum Conditions of Thin-Wall Injection Molding Process (872)

Liao,S.J., Chang,D.Y., Chen,H.J., Tsou,L.S., Ho,J.R., Yau,H.T., Hsieh,W.H., Wang,J.T., Su,Y.C.

Society of Plastic Engineers.
12 国際会議録 Optimization of Injection Molding Conditions Using Thermal Analysis

Hutchins K. M., Kim C. H.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12