Visual Analysis of Fiber Orientation Process by Glass-Inserted Mold. Part 1: Analysis Using a Back-Lighting Method

Visual Analysis of Fiber Orientation Process by Glass-Inserted Mold. Part 1: Analysis Using a Back-Lighting Method

著者名:

Yokoi, H. ( University of Tokyo )
Murata, Y. ( Polyplastics Co., Ltd. )
Nishi, Y. ( Toppan Printing Co., Ltd. )
Seki, T.

掲載資料名:

ANTEC 94 : plastics : gateway to the future : conference proceedings, San Francisco May 1-5 1994 : Volume I. Processing

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

40(1)

発行年:

1994

巻:

1

開始ページ:

392

終了ページ:

396

総ページ数:

5

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/941468

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018760
シリーズID:	PA00000030
会議名:	ANTEC '94 : Annual Technical Conference
回次:	52nd
会議開催地:	San Francisco, CA, USA
会議開催年:	1994.05.01-1994.05.05
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 Visual Analysis of Fiber Orientation Process by Glass-Inserted Mold. Part II: Analysis Using a Fiber Tracing Method Yokoi, H., Murata, Y., Nagaya, N., Harada, H. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Measurement of Melt Temperature Profiles during Filling and packing Processes Using a New Integrated Thermocouple Sensor Yokoi, H., Murata, Y., Tsukakoshi, H. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Visual Analyses of Flow Marks Generation Process Using Glass-Inserted Mold-Part I. Micro-Grooved Flow Marks Yokoi, H., Murata, Y., Nagami, S., Kawasaki, A. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Effect of Fiber Orientation on the Mechanical Properties of an Injection Molded Part and a Stereolithography-Insert Molded Part Damle M., Mehta S., Malloy R., McCarthy P. S. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Visual Analyses of Flow Marks Generation Process Using Glass-Inserted Mold-Part II. Synchronous Flow Marks with Same Phases on Both Top and Bottom Surfaces of … Yokoi, H., Murata, Y., Deguchi, Y., Sakamoto, I. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Long Glass Fiber Thermoplastic Process Development-Part 1 Janosky J. W., Watkins K. H., Gaa C.P. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Visual Analysis of Weld Line Vanishing Process by Glass-Inserted Mold Yokoi, H., Oka, K., Watanabe, H. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Novel x-ray analysis methods using a MicroStrip gas chamber Ochi,A., Tanimori,T., Nishi,Y., Nagayoshi,T., Ohashi,Y., Uekusa,H., Toyokawa,H., Inoue,K., Fujisawa,T. SPIE - The International Society for Optical Engineering
5 国際会議録 Direct Observation of jetting Phenomena under a High Injection Pressure by Using a Prismatic-Glass Inserted Mold Yokoi, H., Hayashi, T., Morikita, N., Toda, K. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 A method for fabricating below 22nm feature patterns in quartz mold A. Terasaki, J. Seki, H. Ono Society of Photo-optical Instrumentation Engineers
6 国際会議録 Visual Observation of Three-Dimensional Melt Flow Inside a Mold Cavity by Gate-Magnetization Method Yokoi, H., Kanematsu, T. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Evaluation Technique of a Polymer Electrolyte Fuel Cell using 1 cm² Cell H. Murata, T. Hatanaka, Y. Morimoto Electrochemical Society

1

2

3

4

5

6

7

8

9

10

11

12