Blank Cover Image

Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

著者名:
Chung, S. T. ( Bestner, Inc. )
Kang, T. G.
Park, S. J.
Kwon, Y. S.
Ahn, H. K.
Yoon, T.
さらに 1 件
掲載資料名:
ANTEC 2001, conference proceedings, Dallas, Texas, May 6-10
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
47
発行年:
2001
パート:
2
開始ページ:
3365
終了ページ:
3368
総ページ数:
4
出版情報:
Brookfield Center, CT: Society of Plastics Engineers
ISBN:
9781587160981 [1587160986]
言語:
英語
請求記号:
S42700/47
資料種別:
国際会議録

類似資料:

1 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
7 国際会議録 An Investigation on the Strength-Porosity Relation in Sintered 17-4 PH STS Produced by Powder Injection Molding

Sung, H.J., Ha, T.K., Ahn, S.H., Chang, Y.W.

Trans Tech Publications
2 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
8 国際会議録 Computer Aided Engineering Design of Powder Injection Molding Process for a Dental Scaler Tip Mold Design

C.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung, B.O. Rhee

Trans Tech Publications
3 国際会議録 Numerical Analysis of Injection/Compression Molding Process for Center-Gated Disc

Park J. S., Han H. J., Ryim G. W., Chang K. S., Kim H. J., Kang G. T., Heo S. B., Kwon H. T.

Society of Plastics Engineers, Inc. (SPE)
9 国際会議録 Impact Analysis of a Dipper-Type and Multi Spring-Type Fuel Rod Support Grid Assemblies in PWR

K. N. Song, K. J. Park, K. H. Yoon, G. J. Park, B. S. Kang

American Society of Mechanical Engineers
4 国際会議録 Filling and Packing CAE Software for Gas Injection Molding

Sherbelis, G.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Injection Molding Cooling System Design

Opolski, S. W., Kwon, T. W.

Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Development of Dental Scaler Tip Mold with Powder Injection Molding Process

C.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung, B.O. Rhee

Trans Tech Publications
11 国際会議録 Sintering Behavior of the Powder Injection Molded Nanocrystalline Fe-50wt%Ni

Nam, H.Y., Kwon, S.K., Kang, Y.S., Lee, J.S.

Trans Tech Publications
6 国際会議録 Computer-Aided Cooling-system Design for Injection Molding

Kwon H. T., Wang K. K.

Society of Plastics Engineers, Inc. (SPE)
12 国際会議録 3D Simulation of the Packing-Cooling Stage in Polymer Injection Molding

Ilinca, F., Hetu, J. -F.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12