Statistical Experiment Study of Gas-Assisted Injection Molding Process

Statistical Experiment Study of Gas-Assisted Injection Molding Process

著者名:

Zhao J. ( Gintic Institute of Manufacturing Technology )
Lu X. ( Gintic Institute of Manufacturing Technology )
Fong L. ( Gintic Institute of Manufacturing Technology )
Chiang H. H.

掲載資料名:

Conference proceedings at ANTEC '98 : plastics on my mind, Society of Plastics Engineers, Atlanta, Georgia, April 26-April 30, 1998

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

44(1)

発行年:

1998

巻:

1

開始ページ:

454

終了ページ:

458

総ページ数:

5

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566766692 [1566766699]

言語:

英語

請求記号:

S42700/44-1

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018301
シリーズID:	PA00000030
会議名:	ANTEC '98 : Annual Technical Conference
回次:	56th
会議開催地:	Atlanta, GA, USA
会議開催年:	1998.04.26-1998.04.30
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 Computer Simulation and Experimental Verification of Gas-Assisted Injection Molding Wang J. T., Chiang H. H., Lu X., Fong L. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 On the Dynamics of Gas-Assisted Injection Molding Process Chang -Y. R., Tsai -H. M., Hsu -H. C. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Non-Destructive Product Characterization of Gas Bubbles in Gas-Assisted Injection-Molded Parts Lu, X., Fong L., Chiang H. H. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Experimental Study of Gas-Assisted Injection Molding Yang, S. Y., Liou, S. J. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Applications of Gas-Assisted Injection Molding and Injection/Compression Molding in Thinwall Molding Wang, T. J., Chen, S. -C., Chiang, H. H. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Transient Gas/Melt Interface and Gas Penetration During Gas-Assisted Injection Molding: Simulation and Experiment Li, C., Shin, J-W., Isayev, A.I., Lee, H-S. Society of Plastics Engineers
4 国際会議録 Optimization Strategies for Injection Molding Turng S. L., Chiang H. H., Stevenson F. J. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Experimental Case Studies of Dimensional Repeatability on Gas Assisted Injection Molding Process and Cavity Pressure Controlled Closed Loop Injection Molding … Okeke E., Cosma L. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Pattern Analysis of Injection Molding Process: Statistical Correlation Study Wu -L. J., Chen J. S. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 An Integrated Design Program for Injection Molding Process Jong R. W., Himasekhar L., Chiang H. H., Wang K. K. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Overcoming Process Control Challenges of Gas-Assist Injection Molding Clark L. C., Williams R., Dixon S. J., Bi S. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Gas-Assisted Rubber Injection Molding Wehr, H., Haberstroh, E. Society of Plastics Engineers

1

2

3

4

5

6

7

8

9

10

11

12