Computer-Aided Gas-Assisted Injection-Molding of the front Cover of Motorcycle Headlight

Computer-Aided Gas-Assisted Injection-Molding of the front Cover of Motorcycle Headlight

著者名:

Chang -Y. R. ( National Tsing-Hua University )
Lin -C. S. ( National Tsing-Hua University )
Chen -C. K. ( Yue Ki Industrial Co., Ltd. )
Hsu -H. C. ( CoreTech System Co., Ltd. )
Tsai -H. M. ( CoreTech System Co., Ltd. )

掲載資料名:

Conference proceedings at ANTEC '98 : plastics on my mind, Society of Plastics Engineers, Atlanta, Georgia, April 26-April 30, 1998

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

44(1)

発行年:

1998

巻:

1

開始ページ:

438

終了ページ:

441

総ページ数:

4

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566766692 [1566766699]

言語:

英語

請求記号:

S42700/44-1

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018301
シリーズID:	PA00000030
会議名:	ANTEC '98 : Annual Technical Conference
回次:	56th
会議開催地:	Atlanta, GA, USA
会議開催年:	1998.04.26-1998.04.30
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 On the Dynamics of Gas-Assisted Injection Molding Process Chang -Y. R., Tsai -H. M., Hsu -H. C. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Computer-Aided-Engineering for the Gas-Assisted Injection Molding Process Turng, L. S. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Numerical Simulations and Experimental Studies of Gas-Assisted Injection Molding Chen, S. C., Hsu, K. S., Jeng, M. C. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Effect of gas channel design on molding window and part mechanical properties of gas-assisted injection molding Chen, S.C., Dong, J.G., Jong, W.R., Huang, J.S., Jeng, M.C. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 The Investigation of Flow Behavior of Polymeric Melts in the Water Assisted Injection Molding Chang, R.Y., Huang, C.T., Yang, W.H., Tsai, M.H., Lu, K.I., Liu, S.J. Society of Plastics Engineers	9 国際会議録 On the PVT and Thermal Shrinkage for the Injection Molding of a Plastic Lens Chang -Y. R., Hsieh -C. Y., Hsu -H. C. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Three-Dimensional Computer-Aided Mold Cooling Design for Injection Molding Chang, R.Y., Hsu, D.C., Yang, V., Yang, W.H. Society of Plastics Engineers	10 国際会議録 Minimize Part Warpage by Integrated CAE Technology Chang -Y. R., Chen -C. Y., Hsu -H. C., Tsai -H. M. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Applications of Gas-Assisted Injection Molding and Injection/Compression Molding in Thinwall Molding Wang, T. J., Chen, S. -C., Chiang, H. H. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Thin-Wall Injection Molding Chen, S. C., Peng, H. S., Huang, L. T., Chang, C. T., Wei, D. Y., Ruo, R. C. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Three-Dimensional Simulation of Gas-Assisted Injection Molding Process Shih, K., Liu, T., Chau, S., Chen, S.C., Lin, Y., Cheng, N-T. Society of Plastics Engineers	12 国際会議録 Study of Polymer Melt Flow during Injection Molding Using Co-Injection Molding Technique Chen, S. C., Hsu, K. F., Jung, W. R. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12