Activity Networks for the Support of Concurrent Engineering of Resin Transfer Molding

Activity Networks for the Support of Concurrent Engineering of Resin Transfer Molding

著者名:

Wright D. ( University of Delaware )
Jones S.
Karbhari V.

掲載資料名:

ANTEC 93 : Be in that number : conference proceedings : New Orleans, May 9-13, 1993

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

39

発行年:

1993

巻:

1

開始ページ:

3256

終了ページ:

3260

総ページ数:

5

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/932082

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018300
シリーズID:	PA00000030
会議名:	ANTEC '93 : Annual Technical Conference
回次:	51st
会議開催地:	New Orleans, LA, USA
会議開催年:	1993.05.09-1993.05.13
論文注記:	TOTAL QUALITY SPECIAL INTEREST GROUP

類似資料:

1 国際会議録 Sensor-Model Control of the Resin Transfer Molding Process Kranbuehl D., Eichinger D., Hamilton T., Levy D., Reyzer M., Kingsley P., Hart S., Loos A., Long R. E. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Neural network application in support of software reliability engineering T.M. Khoshgoftaar, D.L. Lanning, A.S. Pandya Society of Photo-optical Instrumentation Engineers
2 国際会議録 Resin Transfer Molding of BMIs and Polyimides Colton S. J. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 A New Approach to Resin Transfer Molding: Resin Transfer Molding of Truck Cap Panels Mikowski, M. S. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Analysis and Characterization of Flow Channels during Manufacturing of Composites by ]Resin Transfer Molding Mohan V. R., Tamma K. K., Bickerton S., Advani G. S., Shires R. D. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Analytical Modeling and Sensor Monitoring for Optimal Processing of Advanced Textile Structural Composites by Resin Transfer Molding: Infultration Loos A., MacRae J., Hammond V., Kranbuehl E. D., Hart M. S., Hood D., Hasko H. G., Dexter B. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 In situ FDEMS Sensing and Model Verification of Resin Position, Viscosity and Degree of Cure for Resin Transfer Molding of Textile Preforms Loss, A. C., Hammond, V. H., Kranbuehl, D. E., Hood, D., Mahoney, S., Limburg, W., Hasko, G. H. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Analytical Modeling and Sensor Monitoring for Optical Processing of Advanced Textile Structural Composites by Resin Transfer Molding: Infiltration Loos A., MacRae J., Hammond V., Kranbuehl E. D., Hart M. S., Hood D., Hasko H. G., Dexter B. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Analysis of Vacuum Infusion Resin Transfer Molding Ni, J., Li , S., Lee, L. American Institute of Chemical Engineers	11 国際会議録 Low Cost Resin Transfer Molding (TRM) of Foil (Rudder) DeLave D. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Analysis of Vacuum Infusion Resin Transfer Molding with Resin Distribution System Ni J., Li S., Lee J. L. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Low Cost Resin Transfer Molding (RTM) of Foil (Rudder) DeLave D. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12