Trend Regulation of Injection Moulding Process

Trend Regulation of Injection Moulding Process

著者名:

Sercer M. ( Universty of Zagreb )
Catic I.
Baric G.
Perkovic D.

掲載資料名:

ANTEC '97 : plastics saving planet earth, Society of Plastics Engineers, April 27-May 2 : conference proceedings

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

43

発行年:

1997

パート:

1

開始ページ:

556

終了ページ:

560

総ページ数:

5

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566765534 [1566765536]

言語:

英語

請求記号:

S42700/43-1

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00016900
シリーズID:	PA00000030
会議名:	ANTEC '97 : Annual Technical Conference
回次:	55th
会議開催地:	Indianapolis, IN, USA
会議開催年:	1997.04.27-1997.05.02
論文注記:	ANTEC '97, 55th Annual Technical Conference, April 27-May 2, 1997, Indianapolis, USA

類似資料:

1 国際会議録 Injection Moulding Process Studies for Polyketones Martyn T. M., Coates D. P., Bonner G. J., Davidson N. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Numerical Simulation of the Sandwich Injection Moulding Process Schlatter G., Davidoff A., Agassant F. J., Vincent M. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 FE-Analysis of the Two-Step Stretch Blow Moulding Process Rujnic-Sokele, M., Sercer, M., Catic, I. Society of Plastics Engineers	8 国際会議録 Modelling of the Effects of Mould Venting on the Injection Moulding Process Gao M. D., Reymond S., Hetu F. J., Garcia-Rejon A. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Visualization of Injection Moulding Process A.S. Yanev, G.R. Dias, A.M. Cunha Trans Tech Publications	9 国際会議録 Process Optimisation in Elastomer Injection Moulding Menges G., Janke W. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Heat Exchange in Moulds for Steam Moulding of Expandable Polystyrene Jagodic, I., Catic, I., Sercer, M. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 The Use of Process Measurements for Real Time Injection Moulding Process Control Speight, R. G., Coates, P. D., Hull, J. B. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Fluid Assisted Polymer Processing in Extrusion and Injection Moulding: A Comparative Overview Mulvaney-Johnson, L., Woodhead, M., Rose, M., Dawson, A., Gough, T.D., Coates, P.D., Smith, G.F., Goodship, V., … Society of Plastics Engineers	11 国際会議録 Rapid Tooling for Injection Moulding Process Lours, P., Bui, H.V., Nafi, A., Mercier, O., Bernhart, G. Trans Tech Publications
6 国際会議録 TREND REGULATION OF INJECTION MOLDING PROCESS Catic, I. J., Zoric, J. B. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Combined Process Variables and Process Energy Monitoring for Injection Moulding Dawson, A. J., Coates, P. D., Kelly, A. L., Woodhead, M., Collis, R., Owen, L., Owen, D. Society of Plastics Engineers

1

2

3

4

5

6

7

8

9

10

11

12