An approximate analysis and prediction method for tip clearance loss in axial compressors

An approximate analysis and prediction method for tip clearance loss in axial compressors

Author(s):

Storer, J. A. ( Cambridge University )
Cumpsty, N. A.

Publication title:

A.S.M.E. paper

Title of ser.:

ASME Technical Paper : GT

Ser. no.:

1993

Pub. Year:

1993

No.:

93-GT-140

Paper no.:

93-GT-140

Pub. info.:

New York, NY: The American Society of Mechanical Engineers

Language:

English

Call no.:

A11800

Type:

Technical Paper

Details

TDL ID:	ZA00002294
Series ID:	PA00000136
Conf. info. (Name):	International Gas Turbine and Aeroengine Congress and Exposition
Conf. info. (Number):	1993
Conf. info. (Venue):	Cincinnati, Ohio
Conf. info. (Date):	1993.05.24-1993.05.27
Note for article:	Presented at the International Gas Turbine and Aeroengine Congress and Exposition Cincinnati, Ohio - May 24-27, 1993 This paper has been accepted for publication in the Transactions of the ASME Discussion of it will be accepted at ASME Headquarters until September 30, 1993

Similar Items:

1 Technical Paper Interaction of Tip Clearance Flow and Three-Dimensional Separations in Axial Compressors. Gbadebo, S.A., Cumpsty, N.A., Hynes, T.P. American Society of Mechanical Engineers	7 Technical Paper CHARACTERIZATION OF THE TIP CLEARANCE FLOW IN AN AXIAL COMPRESSOR USING DIGITAL PIV Wernet,Mark P., John,W.Trevor, Prahst,P.Susan, Strazisar,Anthony J. American Institute of Aeronautics and Astronautics
2 Technical Paper A METHOD FOR THE PREDICTION OF SUPERSONIC COMPRESSOR BLADE PERFORMANCE Freeman, C, Cumpsty, N A National Aeronautics and Space Adminstration	8 Technical Paper Reduction of Tip Clearance Losses in an Axial Turbine by Shaped Design of the Blade Tip Region. Kusterer, K., Moritz, N., Bohn, D., Sugimoto, T., Tanaka, R. American Society of Mechanical Engineers
3 Technical Paper Control of Tip Clearance Flows in Axial Compressors Bae, J., Breuer, K.S., Tan, C.S. American Institute of Aeronautics and Astronautics	9 Technical Paper Influence of Surface Roughness on Three-Dimensional Separation in Axial Compressors. Gbadebo, S., Hynes, T. P., Cumpsty, N. A. American Society of Mechanical Engineers
4 Technical Paper Stator averaged, rotor blade-to-blade near wall flow in a multistage axial compressor with tip clearance variation Moyle, I. N., Walker, G. J., Shreeve, R. P. The American Society of Mechanical Engineers	10 Technical Paper A method for the calculation of the tip clearance flow effects in axial flow compressors. Part I: Description of basic models. Nikolos, I.K., Douvikas, D.I., Papailiou, K.D. The American Society of Mechanical Engineers
5 Technical Paper Experimental Investigation on the Layout of Tip Clearance for an Axial-Flow Compressor Rotor Zhu, J., Sun, L., Lu, X. American Institute of Aeronautics and Astronautics	11 Technical Paper A method for the calculation of the tip clearance flow effects in axial flow compressors. Part II: Calculation procedure. Nikolos, I.K., Douvikas, D.I., Papailiou, K.D. The American Society of Mechanical Engineers
6 Technical Paper Three-Dimensional Separations in Axial Compressors. Gbadebo, S., Cumpsty, N. A., Hynes, T. P. American Society of Mechanical Engineers	12 Technical Paper DYNAMIC TIP CLEARANCE MEASUREMENTS IN AXIAL FLOW COMPRESSORS Parrish, CJ National Aeronautics and Space Adminstration

1

2

3

4

5

6

7

8

9

10

11

12