An Experimental Study of Cutting Force on Large Cutting Depth Turning Titanium Alloy with CBN Tool

An Experimental Study of Cutting Force on Large Cutting Depth Turning Titanium Alloy with CBN Tool

Author(s):

Publication title:

High Speed Machining VI : Selected, peer reviewed papers from the 6th International Conference on High Speed Machining (ICHSM 2014), July 24-25, 2014, Harbin, China

Title of ser.:

Materials science forum

Ser. no.:

800-801

Pub. Year:

2014

Page(from):

237

Page(to):

240

Pages:

4

Pub. info.:

Aedermannsdorf, Switzerland: Trans Tech Publications

ISSN:

02555476

Language:

English

Call no.:

M23650

Type:

Conference Proceedings

Details

TDL ID:	ZA00054266
Series ID:	PA00000012
Conf. info. (Name):	International Conference on High Speed Machining (ICHSM 2014)
Conf. info. (Number):	6th
Conf. info. (Venue):	Harbin, China
Conf. info. (Date):	2014.07.24-2014.07.25
Note for article:	6th International Conference on High Speed Machining (ICHSM 2014), July 24-25, 2014, Harbin, China

Similar Items:

1 Conference Proceedings Experimental Study of Tool Wear during Quasi High Speed Turning Titanium Alloy with Large Cutting Depth L.F. Xu, W.L. Dong, S.T. Huang, B.L. Dai Trans Tech Publications	7 Conference Proceedings Experimental Study on Cutting Force of High-Speed Micro-Drilling Flexible Printed Circuit Board X. Zhang, C.Y. Wang, L.J. Zheng, L.F. Wang, Y.X. Song Trans Tech Publications
2 Conference Proceedings Experimental Study on Exit Edge Defects in Two Dimension Cutting of SiCp/Al Composites D.J. Zou, S.T. Huang, L. Zhou, L.F. Xu, N. Hou Trans Tech Publications	8 Conference Proceedings Experimental Study on the Tool Wear in Milling Carbon Fiber Reinforced Plastics J.D. Liu, X.F. Yang, Z.L. Xu, Y.S. Li, G.H. Yan, L.K. Huang Trans Tech Publications
3 Conference Proceedings Finite Element Simulation Research on a Large Cutting Depth and Quasi-High Speeds 3-D Milling of Titanium Alloys S.T. Huang, W.Y. Chen, L. Zhou Trans Tech Publications	9 Conference Proceedings Cutting Force Experiment and Simulation by Hard Turning GCr15 Bearing Steel with High Speed Considering Cutting Edge Preparation Y. Wang, F.G. Yan, J.S. Hu, T. Chen, Z. Chang, X.L. Liu Trans Tech Publications
4 Conference Proceedings Study on Finite Element Simulation of the Influence of Cutting Speed on Chip Formation of SiCpAl Composites in High Speed Milling C. Liu, S.T. Huang, K.R. Jiao, L.F. Xu Trans Tech Publications	10 Conference Proceedings Friction Modeling and Experimental Research of Tool-Chip in Turning Titanium Alloy Ti6Al4V Z. Li, E.L. Liu, T.D. Wang, N. Zhao, L.C. Min Trans Tech Publications
5 Conference Proceedings Experimental Study on Surface Quality at Different Milling Speed of High Volume Fraction SiCp/Al Thin Walled Test-Piece K.R. Jiao, S.T. Huang, L.F. Xu Trans Tech Publications	11 Conference Proceedings Experimental Investigation of Tool Wear and Chip Morphology in Turning Titanium Alloy Ti6Al4V Z. Li, E.L. Liu, T.D. Wang, J. Li, Y.C. Zheng Trans Tech Publications
6 Conference Proceedings The Effect of Rare Earth on the Clearance of Carbon during High Speed Polishing of Diamond Films L. Zhou, S.T. Huang, L.F. Xu Trans Tech Publications	12 Conference Proceedings Experimental Study on Turning of Titanium Matrix Composites with PCD Tools H.X. Huan, J.H. Xu, Y.C. Fu, H.H. Su, W.L. Bian Trans Tech Publications

1

2

3

4

5

6

7

8

9

10

11

12