Experimental studies of design guidelines for gas-assisted injection molding process

Experimental studies of design guidelines for gas-assisted injection molding process

Author(s):

Jong, Wen-Ren ( Chung Yuan Christian University, Taiwan )
Huang, Jeng-Sheng
Chang, Yung-Shin

Publication title:

ANTEC '96 : Plastics-Racing into the Future, May 5-10, Indianapolis : conference proceedings

Title of ser.:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

Ser. no.:

42

Pub. Year:

1996

Vol.:

Vol. 1

Page(from):

668

Page(to):

673

Pub. info.:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

Language:

English

Call no.:

S42700/970361

Type:

Conference Proceedings

Details

TDL ID:	ZA00018810
Series ID:	PA00000030
Conf. info. (Name):	ANTEC '96
Conf. info. (Number):	54th
Conf. info. (Venue):	Indianapolis, IN, USA
Conf. info. (Date):	1996.05.05-1996.05.10

Similar Items:

1 Conference Proceedings Effect of gas channel design on molding window and part mechanical properties of gas-assisted injection molding Chen, S.C., Dong, J.G., Jong, W.R., Huang, J.S., Jeng, M.C. Society of Plastics Engineers, Inc. (SPE)	7 Conference Proceedings Experimental Study of Gas-Assisted Injection Molding Yang, S. Y., Liou, S. J. Society of Plastics Engineers, Inc. (SPE)
2 Conference Proceedings Experimental Study of Gas Penetration in the Gas-Assisted Injection Molding (174) Shin,J-W., Isayev,A.I. Society of Plastic Engineers.	8 Conference Proceedings A Basic Study of Rib Geometry for Gas-Assisted Injection Molding Yang Y. S., Huang Z. F. Society of Plastics Engineers, Inc. (SPE)
3 Conference Proceedings Numerical Simulations and Experimental Studies of Gas-Assisted Injection Molding Chen, S. C., Hsu, K. S., Jeng, M. C. Society of Plastics Engineers, Inc. (SPE)	9 Conference Proceedings An experimental study to investigate the influene of processing conditions in the gas-assisted injection molding process Kapila, Vineet, Schott, Nick R., Shah, Suresh Society of Plastics Engineers, Inc. (SPE)
4 Conference Proceedings General Design Guidelines for Gas-Assisted Injection Molding Using a CAE Tool Barton, K. S., Turng, L. S. Society of Plastics Engineers, Inc. (SPE)	10 Conference Proceedings Experimental Case Studies of Dimensional Repeatability on Gas Assisted Injection Molding Process and Cavity Pressure Controlled Closed Loop Injection Molding … Okeke E., Cosma L. Society of Plastics Engineers, Inc. (SPE)
5 Conference Proceedings Optimal Control Design of a Bimorph Optical Beam Deflector Chang-Po Chao, Jeng-Sheng Huang, Ching-Lung Ou Yung, Rong-Fong Fung American Society of Mechanical Engineers	11 Conference Proceedings Structural Analysis, process Si,ulation and Warpage Calculation for the Gas-Assisted Injection Molded Parts Using a Unified CAE Model Chen C. S., Hu Y. S., Jong R. W., Jeng C. M. Society of Plastics Engineers, Inc. (SPE)
6 Conference Proceedings On the Dynamics of Gas-Assisted Injection Molding Process Chang -Y. R., Tsai -H. M., Hsu -H. C. Society of Plastics Engineers, Inc. (SPE)	12 Conference Proceedings Analysis and Design of a Four-Bar Linkage Type of Vibratory Parts Feeder Driven by Piezoelectric Actuator Yung Ting, Min-Sheng Shin, Hong-Yuan Chang American Society of Mechanical Engineers

1

2

3

4

5

6

7

8

9

10

11

12