Designing Premature Failure out of Injection Molded Parts

Designing Premature Failure out of Injection Molded Parts

Author(s):: Mehta, K. S. ( Miles Inc. )
Publication title:: Back to the future : conference proceedings : ANTEC 1992, Detroit, May 3-7
Title of ser.:: Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
Ser. no.:: 38
Pub. Year:: 1992
Pt.:: 2
Page(from):: 2058
Page(to):: 2063
Pages:: 6
Pub. info.:: Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)
Language:: English
Call no.:: S42700/921583
Type:: Conference Proceedings

Details

TDL ID:	ZA00017837
Series ID:	PA00000030
Conf. info. (Name):	ANTEC 1992 : Annual Technical Conference
Conf. info. (Number):	50th
Conf. info. (Venue):	Detroit, MI, USA
Conf. info. (Date):	1992.05.03-1992.05.07
Note for article:	DESIGN SPECIAL INTEREST GROUP
Note:	目次はDivisionごとに分けて掲載されている。論文の順番はDivisionにかかわらず，Session順の通しページになっている。

Similar Items:

1 Conference Proceedings Experimental Stress Analysis for Molded Plastic Parts Mehta S. Kishor Society of Plastics Engineers, Inc. (SPE)	7 Conference Proceedings THE ENGINEER'S GUIDE TO DESIGNING ROTATIONALLY MOLDED PLASTIC PARTS Beall, G. L., Caren, S. Society of Plastics Engineers, Inc. (SPE)
2 Conference Proceedings Structure Performance of Thin-Wall Injection Molded Parts Chen, S. C., Jong, W. R., Chang, Y. P., Kang, Y., Peng, H. S., Huang, L. T., Ynag, L. K., Chang, C. T., Luo, R. C. Society of Plastics Engineers	8 Conference Proceedings Automatic Design Optimization Molding Simulation for Injection Molded Parts Barton, K. S., Lin, B., Ryim, W. G. Society of Plastics Engineers, Inc. (SPE)
3 Conference Proceedings The Effect of Injection Molding Parameters on the Properties of Molded Parts Campbell A. G., Devanathan H., Settlemire S., Sweeney P., Klewicki K., Kenny T., Small D. J., Fricke L. A. Society of Plastics Engineers, Inc. (SPE)	9 Conference Proceedings Weld-Line Strength in Injection Molded PVC Parts Merhar, C. F., Beiter, K. A., Ishii, K. Society of Plastics Engineers, Inc. (SPE)
4 Conference Proceedings Failure Prevention for Injection Molded Medical Devices Woo, L., Ling, M. T. K., Westphal, S. P. Society of Plastics Engineers, Inc. (SPE)	10 Conference Proceedings Control of Dimensional Variability in Injection Molded Plastic Parts Xia Z., Mallick K. P. Society of Plastics Engineers, Inc. (SPE)
5 Conference Proceedings Optimum Design of Process Conditions to Minimize Residual Stresses in Injection-Molded Parts Kang S., Hieber A. C., Wang K. K. Society of Plastics Engineers, Inc. (SPE)	11 Conference Proceedings Halo Surface Defects on Injection Molded Parts Salamon A. B., Koppi A. K., Little J. Society of Plastics Engineers, Inc. (SPE)
6 Conference Proceedings Post-Filling Simulation and Analyses of Shrinkage and Warpage of the Injection Molded Parts Chen, S. -C., Jeng, K. -K. Society of Plastics Engineers, Inc. (SPE)	12 Conference Proceedings Procedures for Increasing the Weldline Strength of Injection Molded Parts Michaeli W., Galuschka S. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12