The Effect of Cutting Speed and Feed Rate on Surface Roughness and Tool Wear when Machining Machining D2 Steel

The Effect of Cutting Speed and Feed Rate on Surface Roughness and Tool Wear when Machining Machining D2 Steel

著者名:

M.R. Ibrahim

掲載資料名:

5th Asia Conference on Mechanical and Materials Engineering

シリーズ名:

Materials science forum

シリーズ巻号:

909

発行年:

2017

開始ページ:

80

終了ページ:

88

総ページ数:

9

出版情報:

Aedermannsdorf, Switzerland: Trans Tech Publications

ISSN:

02555476

ISBN:

9783035712919 [3035712913]

言語:

英語

請求記号:

M23650

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00066581
シリーズID:	PA00000012
会議名:	Asia Conference on Mechanical and Materials Engineering (ACMME 2017)
回次:	5th
会議開催地:	Tokyo, Japan
会議開催年:	2017.06.09-2017.06.11
論文注記:	5th Asia Conference on Mechanical and Materials Engineering (ACMME 2017), June 9-11, 2017, Tokyo, Japan

類似資料:

1 国際会議録 Effect of Variable Pitch on Cutting Temperature, Cutting Forces and Surface Roughness Using Nitico30 Cutting Tool when End Milling of Stainless Steel 316L A. Latif, M.R. Ibrahim, M.S. Mustapa, N.H. Rafai, C. Prakash Trans Tech Publications	7 国際会議録 Research on Relationship between Cutting Conditions and Chip Formation during End Milling of Aluminium Alloy 6061 M.R. Ibrahim, N. Mahadi, A. Latif, Z. Rahim, Z. Mohid, M.S. Mustapa, S.A.C. Ghani Trans Tech Publications
2 国際会議録 Tool Wear and Surface Roughness when Machining AlSi/AlN Metal Matrix Composite Using Uncoated Carbide Cutting Tool M.S. Said, J.A. Ghani, C.H. Che Haron, S. Yusoff, M.A. Selamat Trans Tech Publications	8 国際会議録 Characteristics on Treated Kenaf Fiber Reinforced Polypropylene Composites M.M. Husin, M.S. Mustapa, M.S. Wahab, A.M. Tajul Arifin, R.A.L. Ganasan, F.H. Jais Trans Tech Publications
3 国際会議録 The Cutting Speed Influences on Tool Wear of ZTA Ceramic Cutting Tools and Surface Roughness of Work Material Stainless Steel 316L during High Speed Machining A. Mohd Ali, N.S. Abdullah, M. Ratnam, Z.A. Ahmad Trans Tech Publications	9 国際会議録 Effect of Cutting Tool Materials on Surface Roughness and Cutting Forces in Machining of Al-Si3N4 Composite Produced by Powder Metallurgy Y. Ozcatalbas, E. Bahceci, M. Turker Trans Tech Publications
4 国際会議録 Effect of Tool Wear on Tool Life and Surface Finish when Machining DF-3 Hardened Tool Steel Davoudinejad, Ali, Noordin, M.Y., Ghodsiyeh, Danial, Ashrafi, Sina Alizadeh, Barzani, Mohsen Marani Trans Tech Publications	10 国際会議録 Abrasive Wear on Heat-Treated Recycling Aluminium AA6061 of Various Reinforcement Materials through Powder Metallurgical Process A.S. Mahdi, M.S. Mustapa, M.R.M. Yunus, M.R. Ibrahim, M.I. Ab Kadir, M.W. Ab Rashid Trans Tech Publications
5 テクニカルペーパー Effect of Machining Feed on Surface Roughness in Cutting 6061 Alminum. Kuttolamadom, M., Hamzehlouia, S. Society of Automotive Engineers	11 国際会議録 Analysis of the Behaviour Effect of Face Cutting Edge Inserts on Surface Roughness when Milling Steels with MQL Lubrication Saluena, X., Ortiz, J.A., Casals, J. Trans Tech Publications
6 国際会議録 Experimental Investigation on Surface Roughness and Tool Wear in Dry Machining of TiC Reinforced Aluminium LM6 Composite M. Yusuf, M.K.A. Ariffin, N. Ismail, S. Sulaiman Trans Tech Publications	12 国際会議録 Prediction of Surface Roughness for Periodic End Mill Tool Holder Hadi, Yaser Trans Tech Publications

1

2

3

4

5

6

7

8

9

10

11

12