Blank Cover Image

Parameters Optimization Research of High-Speed Milling PM60 Mould Steel Based on Taguchi Method

著者名:
掲載資料名:
Advances in Materials Processing XII : selected, peer reviewed papers from the 12th Asia-Pacific Conference on Materials Processing (APCMP2016), June 16-19, 2016, Qingdao, China
シリーズ名:
Materials science forum
シリーズ巻号:
861
発行年:
2016
開始ページ:
75
終了ページ:
83
総ページ数:
9
出版情報:
Aedermannsdorf, Switzerland: Trans Tech Publications
ISSN:
02555476
ISBN:
9783038356349 [3038356344]
言語:
英語
請求記号:
M23650 [v.861]
資料種別:
国際会議録

類似資料:

1 国際会議録 Chip Formation of S790 Hardned Steel under High Speed Dry Milling Condition

D.H. Yu, H. Wang, C.Y. Wang, Y.H. Yuan, F. Ding

Trans Tech Publications
7 国際会議録 Experimental Study of the Corner of Hardened Steel Mould in High Speed Milling with Micro-End Mill

B.X. Dong, Y.N. Hu, S.S. Hu, X. Huang

Trans Tech Publications
2 国際会議録 Experiment on Optimal Selecting for Cutting Tools in Milling of High Hardened Steel

K.P. Zhang, C.Y. Wang, Y.N. Hu, Y.X. Song

Trans Tech Publications
8 国際会議録 The Multi-Objective Optimization on Milling Parameters of Ultra-High Strength Steel 30Cr3SiNiMoVA

J.B. Song, C.Y. Wang, P.L. Liu, L. Zhan, M. Chen

Trans Tech Publications
3 国際会議録 Evaluation Methods Research Based on the Concrete with Rheological Properties

J.C. Lin, Y.X. Gao, W.Q. Li, X. Wu, Y.X. Huang

Trans Tech Publications
9 国際会議録 The research about high-speed optical recording wave and optimum power parameter model

Liu, C., Xie, C., Huang, H., Wang, H., Han, D.

SPIE - The International Society of Optical Engineering
4 国際会議録 Research on Cutting Vibration in High-Speed Milling Nickel-Base Superalloy

C. Zhao, Z.B. Wang, X.H. Wang, W. Xi, Y.Y. Shi

Trans Tech Publications
10 国際会議録 The Experimental Modal Analysis of High Speed Machining Tool System Based on Integral Polynomial Recognition Method

F. Xiao, X.L. Liu, Y.X. Wang, L.J. Liu, D. Qu

Trans Tech Publications
5 国際会議録 Evaluation Methods Research Based on the Concrete with Rheological Properties

J.C. Lin, Y.X. Gao, W.Q. Li, X. Wu, Y.X. Huang, Y. Peng

Trans Tech Publications
11 国際会議録 The Optimization of Cutting Parameters for Surface Roughness in High Speed Milling Based on Taguchi Method

P.N. Li, M. Chen, X.J. Kang, L.N. Zhang, M. Zhou

Trans Tech Publications
6 国際会議録 Experimental Study on Cutting Force of High-Speed Micro-Drilling Flexible Printed Circuit Board

X. Zhang, C.Y. Wang, L.J. Zheng, L.F. Wang, Y.X. Song

Trans Tech Publications
12 国際会議録 Geometry Optimization of D-Type Micro End-Mill with FEM Analysis

X.H. Zheng, C.Y. Wang, X.B. Wang, Z.W. Xu, M. Chen

Trans Tech Publications
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12