Edge Cutting Tools for Machining of Hard-to-Cut Materials

Edge Cutting Tools for Machining of Hard-to-Cut Materials

著者名:

掲載資料名:

Advanced Materials Engineering and Technology IV : selected peer reviewed papers from the 2015 International Conference on Advanced Materials Engineering and Technology (ICAMET 2015), December 4-5, 2015, Kaohsiung,Taiwan

シリーズ名:

Materials science forum

シリーズ巻号:

857

発行年:

2016

開始ページ:

213

終了ページ:

220

総ページ数:

8

出版情報:

Aedermannsdorf, Switzerland: Trans Tech Publications

ISSN:

02555476

ISBN:

9783035710205 [3035710201]

言語:

英語

請求記号:

M23650 [v.857]

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00055305
シリーズID:	PA00000012
会議名:	International Conference on Advanced Materials Engineering and Technology - ICAMET 2015
回次:	2015
会議開催地:	Kaohsiung,Taiwan
会議開催年:	2015.12.04-2015.12.05
論文注記:	2015 International Conference on Advanced Materials Engineering and Technology (ICAMET 2015), December 4-5, 2015, Kaohsiung,Taiwan

類似資料:

1 国際会議録 Control of Temperature in Cutting Zone in Machining of Alloyed Case-Hardened Steels by Applying a Ceramic Tool with Wear-Resistant Coatings A.A. Vereshchaka, J. Prilukova, A.S. Vereshchaka, J. Bublikov, A. Aksenenko Trans Tech Publications	7 国際会議録 Application of Self-Propagating High-Temperature Synthesis and Mechanoactivating Treatment for Producing Multi-Component Composite Alloying Materials Yakovlev, V.I., Sobachkin, A.V., Sitnikov, A.A. Trans Tech Publications
2 国際会議録 Specifics of Application of Cutting Ceramics with Functional Coating in Turning of High-Strength Materials A.A. Vereshchaka, J. Prilukova, B.Y. Mokritskii, A.S. Vereshchaka, N. Sitnikov Trans Tech Publications	8 国際会議録 The Cutting Speed Influences on Tool Wear of ZTA Ceramic Cutting Tools and Surface Roughness of Work Material Stainless Steel 316L during High Speed Machining A. Mohd Ali, N.S. Abdullah, M. Ratnam, Z.A. Ahmad Trans Tech Publications
3 国際会議録 Comparative Evaluation of Properties of Various Tool Materials by Area of Indentation Track in Pendulum Scratch Testing A.A. Vereshchaka, B.Y. Mokritskii, A.S. Vereshchaka Trans Tech Publications	9 国際会議録 Cutting Force Experiment and Simulation by Hard Turning GCr15 Bearing Steel with High Speed Considering Cutting Edge Preparation Y. Wang, F.G. Yan, J.S. Hu, T. Chen, Z. Chang, X.L. Liu Trans Tech Publications
4 国際会議録 Edge Preparation on Cutting Force, Cutting Temperature and Tool Wear for Hard Turning P.R. Zhang, Z.Q. Liu Trans Tech Publications	10 国際会議録 Diffusion Wear and Oxidation Wear of PCBN Tool when Cutting Materials Difficult-to-Cut Based on Thermodynamics Solubility F. Shao, Y.T. Wang, J.H. Li Trans Tech Publications
5 国際会議録 Periodic Motions of the Machine Tools in Cutting Process Brandon C. Gegg, Steve S. Suh, Albert C. J. Luo American Society of Mechanical Engineers	11 国際会議録 Environmentally-Assisted Hard Materials Machining Pertsov V. N. Noordhoof International Publishing
6 国際会議録 Microstructural Differences of Adhered Material in the Tool Edge and Tool Rake Face. Application to the Machining of Al Alloys Sanchez, J. M., Sebastian, M. A., Gonzalez, J. M., Carrilero, M. S., Marcos, M. Trans Tech Publications	12 国際会議録 Cutting Force Analysis in Tool Condition Monitoring of Difficult to Cut Materials Z.R. Liao, D. Gao, Y. Lu Trans Tech Publications

1

2

3

4

5

6

7

8

9

10

11

12