Blank Cover Image

Flow Front Behavior During Co-Injection Mold Filling

著者名:
掲載資料名:
Proceedings of the 3rd ASME・JSME Joint Fluids Engineering Conference : presented at the 3rd ASME・JSME Fluids Engineering Conference, July 18-23, 1999, San Francisco, California
シリーズ名:
ASME Symposia Volumes
シリーズ巻号:
FEDSM 1999
発行年:
2000
パート:
5
ペーパー番号:
FEDSM99-7094
開始ページ:
47
終了ページ:
52
総ページ数:
6
出版情報:
New York, N.Y.: American Society of Mechanical Engineers
ISBN:
9780791819784 [0791819787]
言語:
英語
請求記号:
A11646/1999
資料種別:
国際会議録

類似資料:

1 国際会議録 Effect of the Skin/Core Ratio on the Flow Behaviour during Co-Injection Moulding

Derdouri, A., Garcia-Rejon, A., Nguyen, K. T., Simard, Y., Koppi, K. A., Salamon, B. A.

Society of Plastics Engineers, Inc. (SPE)
7 国際会議録 Gravity Effects during Mold Filling: Fluid Front Dynamics

Altan,M.C., Olivero,K.A.

American Chemical Society
2 国際会議録 Polymer Melt Flow Behavior in the Coinjection Molding Process

Nguyen, K. T., Turcott, E., Derdouri, A., Messaoud, D. A., Sanschagrin, B., Salamon, B. A., Koppi, K. A.

Society of Plastics Engineers, Inc. (SPE)
8 国際会議録 Numerical Simulation and Experimental Validation of the Filling Stage in the Co-Injection Molding Process

Ilinca, F., Derdouri, A., Hetu, J-F., Messaound, D.A., Sanchagrin, B.

Society of Plastics Engineers
3 国際会議録 Effect of Variable Injection Speed in Injection Mould Filling

Gao, D. M., Nguyen, K. T., Girard, P., Salloum, G.

Society of Plastics Engineers, Inc. (SPE)
9 国際会議録 Simulation of the Injection Molding of Thermosetting Polymers

Nguyen T. K., Kabanemi K. K., Gao M. D.

Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Numerical Simulation of the Sequential Filling in Injection Molding Process

Gao, D. M., Nguyen, K. T., Girard, P., Salloum, G.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Prediction of Microstructure Development During Injection Mold Filling (The McKam-II Model)

Chu, E., Goyal, S. K., Kamal, M. R.

Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Polymer Flow Length Simulation During Injection Mold Filling

Buchmann M., Theriault P. R., Osswald A. T.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Halo Surface Defects on Injection Molded Parts

Salamon A. B., Koppi A. K., Little J.

Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Study on Mechanical Properties and Material Distribution of Sandwich Plaques Molded By Co-Injection

Ait Messaoud, D., Sanschagrin, B., Derdouri, A.

Society of Plastics Engineers
12 国際会議録 Modeling and Simulation of High Reynolds' Number Flows During Reaction Injection Mold Filling

Spiegelhoff J. T., Osswald A. T.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12