Investigation of Sintering Behaviors of Steatite Parts Produced by Powder Injection Molding

Investigation of Sintering Behaviors of Steatite Parts Produced by Powder Injection Molding

著者名:

掲載資料名:

Progress in powder metallurgy : proceedings of the 2006 Powder Metallurgy World Congress & Exhibition (PM 2006), held in Busan Exhibition & Convention Center (BEXCO), Busan, Korea, September 24-28, 2006

シリーズ名:

Materials science forum

シリーズ巻号:

534-536

発行年:

2007

パート:

1

開始ページ:

549

終了ページ:

552

総ページ数:

4

出版情報:

Aedermannsdorf, Switzerland: Trans Tech Publications

ISSN:

02555476

ISBN:

9780878494194 [0878494197]

言語:

英語

請求記号:

M23650

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00046592
シリーズID:	PA00000012
会議名:	Powder Metallurgy World Congress & Exhibition - PM
回次:	2006
会議開催地:	Busan, Korea
会議開催年:	2006.09.24-2006.09.28

類似資料:

1 国際会議録 Effect of Heat Treatment Conditions and Densities on Residual Stresses at Hybrid (FLN2-4405) P/M Steels F. Kafkas, C. Karatas, S. Saritas Trans Tech Publications	7 国際会議録 Powder Injection Molding of Ti6Al4V Alloy X.H. Qu, S.B. Guo, C.F. Tang, M.L. Qin, X.B. He, S.H. Islam Trans Tech Publications
2 国際会議録 An Investigation on the Strength-Porosity Relation in Sintered 17-4 PH STS Produced by Powder Injection Molding Sung, H.J., Ha, T.K., Ahn, S.H., Chang, Y.W. Trans Tech Publications	8 国際会議録 Polyethylene Powder Characteristics: Impact on Polymer Sintering and Rotational Molding Guillen-Castellanos, S. A., Bellehumeur, C. T., Weber, M. Society of Plastics Engineers
3 国際会議録 Investigation on Thermal Debinding of Powder Injection Molding Lam, Y.C., Shengjie, Y., Lam, K.H., Ma, J., Tam, K.C., Yu, S.C.M. Trans Tech Publications	9 国際会議録 Counter Flow Injection Molding - An Alternative Method for Producing Parts with Sandwich-Like Morphology Tchalamov, D.B., Viana, J.C., Cunha, A.M. Society of Plastics Engineers
4 国際会議録 Corrosion and Cytotoxicity Evaluation of AISI 316L Stainless Steel Produced by Powder Injection Molding (PIM) Technology Costa, I., Rogero, S. O., Correa, O. V., Kunioshi, C. T., Saiki, M. Trans Tech Publications	10 国際会議録 Sintering Behavior of Iron Aluminide Powders Gedevanishvili, S., Deevi, S.C. Trans Tech Publications
5 国際会議録 The Investigation of Flow Behavior of Polymeric Melts in the Water Assisted Injection Molding Chang, R.Y., Huang, C.T., Yang, W.H., Tsai, M.H., Lu, K.I., Liu, S.J. Society of Plastics Engineers	11 国際会議録 The Effects of Isothermal Molding on Powder Injection Molding Woodward W. S., Dasch M. K. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Gelcasting of Stainless Steel Powder: An Alternative to Injection Molding F.S. Ortega, R.L.S. Oliveira, M.C. Plínio, B.N. Nobrega Trans Tech Publications	12 国際会議録 The Effects of Isothermal Molding on Powder Injection Molding Woodward W. S., Dasch M. K. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12