Blank Cover Image

Development of Dental Scaler Tip Mold with Powder Injection Molding Process

著者名:
掲載資料名:
Progress in powder metallurgy : proceedings of the 2006 Powder Metallurgy World Congress & Exhibition (PM 2006), held in Busan Exhibition & Convention Center (BEXCO), Busan, Korea, September 24-28, 2006
シリーズ名:
Materials science forum
シリーズ巻号:
534-536
発行年:
2007
パート:
1
開始ページ:
345
終了ページ:
348
総ページ数:
4
出版情報:
Aedermannsdorf, Switzerland: Trans Tech Publications
ISSN:
02555476
ISBN:
9780878494194 [0878494197]
言語:
英語
請求記号:
M23650
資料種別:
国際会議録

類似資料:

1 国際会議録 Computer Aided Engineering Design of Powder Injection Molding Process for a Dental Scaler Tip Mold Design

C.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung, B.O. Rhee

Trans Tech Publications
7 国際会議録 Influence of Sintering Process on the Mechanical Properties of Dental Zirconia Ceramics

W.U. Park, J.M. Zhao, K.H. Hwang, T.S. Kim, C.H. Yu

Trans Tech Publications
2 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
8 国際会議録 The Effect of Injection Molding Parameters on the Properties of Molded Parts

Campbell A. G., Devanathan H., Settlemire S., Sweeney P., Klewicki K., Kenny T., Small D. J., Fricke L. A.

Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
9 国際会議録 Influence of Powder Geometry on Powder Injection Molding Process Parameters

Resende, L.M., Prata, A.T., Klein, A.N., Almeida, L.H.S.

Trans Tech Publications
4 国際会議録 Integrated CAE Analysis for Powder Injection Molding: Filling, Packing and Cooling Stages

Chung, S. T., Kang, T. G., Park, S. J., Kwon, Y. S., Ahn, H. K., Yoon, T.

Society of Plastics Engineers
10 国際会議録 Powder Injection Molding of Ti6Al4V Alloy

X.H. Qu, S.B. Guo, C.F. Tang, M.L. Qin, X.B. He, S.H. Islam

Trans Tech Publications
5 国際会議録 Effect of Particle Size in Feedstock Properties in Micro Powder Injection Molding

E.R. Baek, S. Supriadi, C.J. Choi, B.T. Lee, J.W. Lee

Trans Tech Publications
11 国際会議録 Numerical Analysis of Injection/Compression Molding Process for Center-Gated Disc

Park J. S., Han H. J., Ryim G. W., Chang K. S., Kim H. J., Kang G. T., Heo S. B., Kwon H. T.

Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Microcelluar Nnocomposite Injection Molding Process

Yuan, M., Turng, L-S.T., Spindler, R., Caulfield, D.F., Hunt, C.

Society of Plastics Engineers
12 国際会議録 Scaling Methodology for the Direct ECC Bypass During LBLOCA Reflood Phase With Direct Vessel Injection System: Its Development and Validation

H. K. Cho, B. J. Yun, T. S. Kwon, C.-H. Song, G. C. Park

American Society of Mechanical Engineers
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12