Injection Molding of Polyetherimide Using Water Cooled Molds

Injection Molding of Polyetherimide Using Water Cooled Molds

著者名:

Bixby, G.F. ( General Electric Plastics )
Sanner, M.A.

掲載資料名:

ANTEC 2003, annual technical conference, May 4-8, Nashville, Tennessee

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

61

発行年:

2003

開始ページ:

1847

終了ページ:

1852

総ページ数:

6

出版情報:

Brookfield Center, Conn.: Society of Plastics Engineers

ISBN:

9780972718011 [097271801X]

言語:

英語

請求記号:

S42700/61-2

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00012897
シリーズID:	PA00000030
会議名:	ANTEC : Annual Technical Conference
回次:	2003 : 61st
会議開催地:	Nashville, TN, USA
会議開催年:	2003.05.04-2003.05.08
論文注記:	THERMOPLASTIC MATERIALS AND FOAMS DIVISION

類似資料:

1 国際会議録 Injection Molding of a High Flow Polyetherimide - Polycarbonate Ester Blend Sanner, M.A., May, A. Society of Plastics Engineers	7 国際会議録 Conductive Polymer Blends for Injection-Molded Bipolar Plates Huneault, M.A., Mighri, F., Champagne, M.F. Society of Plastics Engineers
2 国際会議録 Mold Release Agents for Polyetherimides Gallucci, R.R., Sanner, M.A. Society of Plastics Engineers	8 国際会議録 Evaluation of Variability in Injection Molding (IM) Molds Jantharawong, A., Cabrera Rios, M., Lilly, B., Castro, J.M. Society of Plastics Engineers
3 国際会議録 Estimating Cooling Water Requirements for Injection Molding Plants Kupchella M. B. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Heat Transfer Measurement at the Mold Surface During Injection Molding of Thermoplastic Melts Kamal, M. R., Salloum, G., Garcia-Rejon, A. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Injection-Molded Core-Preforms for Polarization-Maintaining Single-Mode HMFG Fibers Kober,A., West,G.F., Tobben,H., Wetenkamp,L. Trans Tech Publications	10 国際会議録 Rapid Tooling: A Study of Different Cooling Techniques for Mold Inserts Used in the Direct AIM (ACES Injection Molding )Process Saurkar, S., Malloy, R., McCarthy, S. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 How to Use the Mold Filling and Mold Cooling Programs to Solve Mold Design and Molding Problems Bernhard, M., Hsu, C. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Safety Considerations for Low Cost Quick Mold Hydraulic Clamp Systems Applying to the Injection Molding Industry Schroeder, F. W., Grosser, G. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Gap between mold and part and its effect on cooling of injection-molded plastics Wang, H., Prystay, M., Hetu, J.-F., Cao, B., Jen, C.K. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Phenolic Composites with Recycled Paper Fibers Deanin, R. D., Bixby, G. F. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12