Microcelluar Nnocomposite Injection Molding Process

Microcelluar Nnocomposite Injection Molding Process

著者名:

Yuan, M. ( University of Wisconsin-Madison )
Turng, L-S.T.
Spindler, R. ( Kaysun Corporation )
Caulfield, D.F. ( U.S.D.A. Forest Products Laboratory )
Hunt, C.

掲載資料名:

ANTEC 2003, annual technical conference, May 4-8, Nashville, Tennessee

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

61

発行年:

2003

開始ページ:

691

終了ページ:

695

総ページ数:

5

出版情報:

Brookfield Center, Conn.: Society of Plastics Engineers

ISBN:

9780972718011 [097271801X]

言語:

英語

請求記号:

S42700/61-1

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00012896
シリーズID:	PA00000030
会議名:	ANTEC : Annual Technical Conference
回次:	2003 : 61st
会議開催地:	Nashville, TN, USA
会議開催年:	2003.05.04-2003.05.08
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 Application of Polyamide/Cellulose Fiber/Wollastonite Composites for Microcellular Injection Molding Winata, H., Turng, L-S.T., Caulfield, D.F., Kuster, T., Spindler, R., Jacobson, R.E. Society of Plastics Engineers	7 国際会議録 Modeling Cell Nucleation During Microcellular Injection Molding Hernandez, J.P., Chandra, A., Winardi, A., Osswald, T.A., Turng, L-S.T., Gramann, P. Society of Plastics Engineers
2 国際会議録 Microcellular Injection Molding Turng, L-S.T. Society of Plastics Engineers	8 国際会議録 Development of an Integrated Computer-Aided Engineering and Optimization System for Injection Molding (660) Peic,M., Turng,L-S. Society of Plastic Engineers.
3 国際会議録 Numerical Analysis of Microcelluar Injection Molding Han, S., Kennedy, P., Zheng, R., Xu, J., Kishbaugh, L. Society of Plastics Engineers	9 国際会議録 Simulation of Co-Injection and Gas-Assisted Injection Molding Turng, L. S. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 A Web-Based Knowledge Management System for the Injection Molding Process Turng, L. -S., DeAugistine, D. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Optimization Strategies for Injection Molding Turng S. L., Chiang H. H., Stevenson F. J. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Computer-Aided-Engineering for the Gas-Assisted Injection Molding Process Turng, L. S. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Thin-Wall Injection Molding Chen, S. C., Peng, H. S., Huang, L. T., Chang, C. T., Wei, D. Y., Ruo, R. C. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 New Developments in CAET Technology for the Gas-Assisted Injection Molding Process Turng S. L. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 General Design Guidelines for Gas-Assisted Injection Molding Using a CAE Tool Barton, K. S., Turng, L. S. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12