Blank Cover Image

Geometric Variation of Micro-Features in Injection Molding Experiment

著者名:
掲載資料名:
ANTEC 2003, annual technical conference, May 4-8, Nashville, Tennessee
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
61
発行年:
2003
開始ページ:
597
終了ページ:
601
総ページ数:
5
出版情報:
Brookfield Center, Conn.: Society of Plastics Engineers
ISBN:
9780972718011 [097271801X]
言語:
英語
請求記号:
S42700/61-1
資料種別:
国際会議録

類似資料:

1 国際会議録 Ultrasonic Cavity Sensors for Micro-Molding

Thomas, C.L., Lee, S.K., Cuff, D., Huilgol, N.N.

Society of Plastics Engineers
7 国際会議録 Cavity Based Ultrasonic Resonance Monitoring in Injection Molding (1098)

Edwards,R., Diao,L., Thomas,C.L., Groleau,M.

Society of Plastic Engineers.
2 国際会議録 Development of a Micro/Nano Injection Molding Testbed

Thomas, C.L., Lee, S.

Society of Plastics Engineers
8 国際会議録 A Comparison of Position, Cavity Pressure, and Ultrasound Sensors for Switch/Over Control in Injection Molding

Thomas, C.L., Edwards, R., Diao, L.

Society of Plastics Engineers
3 国際会議録 Rapid tooling using SU-8 for injection molding microfluidic components

Edwards,T.L., Mohanty,S.K., Edwards,R.K., Thomas,C.L., Frazier,A.B.

SPIE-The International Society for Optical Engineering
9 国際会議録 Critical factors for nanoscale injection molding [6380-21]

Yoon, S., Lee, J., Park, K., Mead, J. L., Matsui, S., Barry, C. M. F.

SPIE - The International Society of Optical Engineering
4 国際会議録 Experimental and Numerical Analysis of Thin-Wall Injection Molding with Micro-Features

Yu, L., Koh, C. G., Koelling, K. W., Lee, L. J., Madou, M. J.

Society of Plastics Engineers
10 国際会議録 Effect of Particle Size in Feedstock Properties in Micro Powder Injection Molding

E.R. Baek, S. Supriadi, C.J. Choi, B.T. Lee, J.W. Lee

Trans Tech Publications
5 国際会議録 On-Line Monitoring of Polymer Orientation during Injection Molding

Edwards, R., Thomas, C.L., Bur, A. J.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Optical Monitoring of polypropylene Injection Molding

Bur J. A., Thomas L. C.

Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Effects of Materials When Injection Molding Nano-scale Features

Srirojpinyo, C., Yoon, S.H., Lee, J., Sung, C., Mead, J.L., Barry, C.F.

Society of Plastics Engineers
12 国際会議録 Simulation of the Micro Injection Molding Process

Kemmann, O., Weber, L., Jeggy, C., Magotte, O., Dupret, F.

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12