The Cost of Tolerances in Injection Molded Parts (741)

The Cost of Tolerances in Injection Molded Parts (741)

著者名:

Bernhardt,A. ( Plastics & Computer Inc. )
Wolverton,M.P. ( Huntsman Corp. )

掲載資料名:

ANTEC 2002, annual technical conference, San Francisco, CA, May 5-9, 2002

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

60

発行年:

2002

巻:

3

開始ページ:

2986

終了ページ:

2986

総ページ数:

1

出版情報:

Brookfield, Conn.: Society of Plastic Engineers.

ISBN:

9780971643505 [0971643504]

言語:

英語

請求記号:

S42700/60

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00012351
シリーズID:	PA00000030
会議名:	ANTEC 2002 : Annual Technical Conference
回次:	2002
会議開催地:	San Francisco, CA, USA
会議開催年:	2002.05.09-2002.05.09
論文注記:	PRODUCT DESIGN AND DEVELOPMENT DIVISION

類似資料:

1 国際会議録 Computer Modeling Predicts the Dimensional Tolerances of Molded Parts Bernhardt C. E. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Adibabatic Splay and Blush in Injection Molded Parts Van Huffel, P.F. Society of Plastics Engineers
2 国際会議録 Managing Risk in New Product Development Bernhardt A., Wolverton M. P. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Effects of Complexity on Tooling Cost and Time-to-Market of Plastic Injection Molded Parts Fagade, A., Kazmer, D. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Design for Cost of Plastic Injection Molded Parts Merino, D. W. Jr., Merino, D. N. Sr. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Conformational Deformation of Linear Polymers in Injection Molded Parts Okumura, M., Nagasawa, M. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 The Effect of Direct Electrical Heating on the Cycle Time and Mechanical Properties of Rotationally Molded Polyethylene Parts Kearns, M.P., Daly, C., Crawford, R.J. Society of Plastics Engineers	10 国際会議録 Shrinkage Analysis of Reinforced Injection Molded Parts Sanschagrin B., Rivard S., Hebert P. L., Girard P. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Control of Dimensional Variability in Injection Molded Plastic Parts Xia Z., Mallick K. P. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Why It Is Difficult to Mold Parts within Tolerance in Pattern Based Injection Mold Tooling Mueller, T. J. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Estimating the Cycle Time in Injection Molded Amorphous Parts Dickerson, J. P. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Sink Mark Study in Injection Molded Parts Liou J. M., Ramachandra M. D., Ishii K., Hornberger L. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12