Linear Shrinkage Differences in Plastic Injection Molded Parts

Linear Shrinkage Differences in Plastic Injection Molded Parts

著者名:

Velarde, D. A. ( Pennsylvania State University at Erie, The Behrend College )
Yeagley, M. J.

掲載資料名:

ANTEC 2000 Conference proceedings, May 7-11, 2000, Orlando, Florida

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

46

発行年:

2000

パート:

1

開始ページ:

3466

終了ページ:

3469

総ページ数:

4

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566768559 [1566768551]

言語:

英語

請求記号:

S42700/46

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00021094
シリーズID:	PA00000030
会議名:	ANTEC 2000 : Annual Technical Conference
回次:	58th
会議開催地:	Orlando, FL, USA
会議開催年:	2000.05.07-2000.05.11
論文注記:	MOLD MAKING/MOLD DESIGN DIVISION

類似資料:

1 国際会議録 Linear Shrinkage Differences in Plastic Injection Molded Parts Velarde, D. A., Yeagley, M. J. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Design for Cost of Plastic Injection Molded Parts Merino, D. W. Jr., Merino, D. N. Sr. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Studies on the Influence of the Holding Pressure on the Orientation and Shrinkage of Injection Molded Parts (98) Pontes,A.J., Oliveira,M.J., Pouzada,A.S. Society of Plastic Engineers.	8 国際会議録 Sink Mark Study in Injection Molded Parts Liou J. M., Ramachandra M. D., Ishii K., Hornberger L. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Validation of Shrinkage Predications for Injection Molded Parts Prasad, S., Sharma, S., Jariwala, M., Barry, C.M.F. Society of Plastics Engineers	9 国際会議録 Conformational Deformation of Linear Polymers in Injection Molded Parts Okumura, M., Nagasawa, M. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Validation of Shrinkage Predictions for Injection Molded Parts Prasad, S.H., Jariwala, M., Sharma, S.S., Barry, C.F., Malur, V. Society of Plastics Engineers	10 国際会議録 Predicting Shrinkage for Injection Molds Bogdanski, B., McMeans, M., Bogdanski, P. Society of Plastics Engineers
5 国際会議録 Modeling of Sink Mark Formation in Cross-Rib-Reinforced Injection-Molded Plastic Parts by Localized Finite Element Shrinkage Analysis Shi, L., Gupta, M. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Computer Mold Cooling Simulation of Injection Molded Plastic Parts Schoen, R., McDonald, D. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Prediction of Sink Marks in Injection-Molded Plastic Parts Using a Localized Shrinkage Analysis Near a Rib Shi L., Gupta M. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Shrinkage and Warpage Behavior of Injection Molded Nylon 6 and PET Bars and Plates Lee S. C., Dubin A., Sarkar K., Squire R. K., Vorres L. C., Yuhas E. D., Blechl J. M. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12