Blank Cover Image

Modelling and Validation of the Blow Moulding of HDPE/Nylon Multilayer Containers

著者名:
掲載資料名:
ANTEC 2000 Conference proceedings, May 7-11, 2000, Orlando, Florida
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
46
発行年:
2000
パート:
1
開始ページ:
879
終了ページ:
883
総ページ数:
5
出版情報:
Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)
ISBN:
9781566768559 [1566768551]
言語:
英語
請求記号:
S42700/46
資料種別:
国際会議録

類似資料:

1 国際会議録 Heat Transfer Dynamics of the Cooling and Solidification Phase of Blow Moulding

DiRaddo, R. W., Garcia-Rejon, A.

Society of Plastics Engineers, Inc. (SPE)
7 国際会議録 Transient Heat Transfer Coefficients for the Solidification of Blow Molded Parts

Masse, H., Debergue, P., DiRaddo, R.

Society of Plastics Engineers
2 国際会議録 Recycling of Polyolefins in Blow Moulding

DiRaddo, R. W., Pecora, L., Garcia-Rejon, A., Inch, J. I.

Society of Plastics Engineers, Inc. (SPE)
8 国際会議録 Annular Swell in Multilayer Flow of Virgin and Recycled Polymers

Garcia -Rejon A., Diraddo W. R., Dube A. F.

Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Recycling of Polyolefins Blow Moulding

DiRaddo, R. W., Pecora, L., Garcia-Rejon, A., Inch, J. I.

Society of Plastics Engineers, Inc. (SPE)
9 国際会議録 Wall Thickness Distribution in Blow Moulded Products: Comparison between Theoretical Predictions and Experimental Results

Garcia-Rejon, A., Schoebe, S., DiRaddo, R. W.

Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Neural Network Modelling of the Injection Stage in Blow Molding

DiRaddo W. R., Garcia-Rejon A.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Multilayer Flow Behavior Insider Blow Moulding Dies

Dufour, S., Pelletier, D., Hetu, J., Garcia-Rejon, A.

American Institute of Chemical Engineers
5 国際会議録 Modelling the Effect of Operating Conditions on the Blow Moulding of an Gas Tank

Laroche D., DiRaddo W. R., Pecora L., Garcia-Rejon A., Bolouri B., Atsbha H.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Control of State Parameters in Blow Moulding (43)

DiRaddo,R., Girard,P., Laroche,I.

Society of Plastic Engineers.
6 国際会議録 Numerical Simulation and Experimental Techniques Applied to Extrusion Blow Molding

Garcia-Rejon A., DiRaddo W. R.

Society of Plastics Engineers, Inc. (SPE)
12 国際会議録 Design and Optimization of Planar Automotive Blow Moulded Parts (45)

Thibault,F., Debergue,P., Laroche,D., DiRaddo,R., Milliste,M.

Society of Plastic Engineers.
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12