Blank Cover Image

Preventing Sink Marks of Injection Molded Parts Using CAE Analysis

著者名:
Ni, S. ( Lexmark International Inc. )  
掲載資料名:
ANTEC 2000 Conference proceedings, May 7-11, 2000, Orlando, Florida
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
46
発行年:
2000
パート:
1
開始ページ:
453
終了ページ:
460
総ページ数:
8
出版情報:
Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)
ISBN:
9781566768559 [1566768551]
言語:
英語
請求記号:
S42700/46
資料種別:
国際会議録

類似資料:

1 国際会議録 Structural Analysis, process Si,ulation and Warpage Calculation for the Gas-Assisted Injection Molded Parts Using a Unified CAE Model

Chen C. S., Hu Y. S., Jong R. W., Jeng C. M.

Society of Plastics Engineers, Inc. (SPE)
7 国際会議録 Shrinkage Analysis of Reinforced Injection Molded Parts

Sanschagrin B., Rivard S., Hebert P. L., Girard P.

Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Prediction of Sink Marks in Injection-Molded Plastic Parts Using a Localized Shrinkage Analysis Near a Rib

Shi L., Gupta M.

Society of Plastics Engineers, Inc. (SPE)
8 国際会議録 Modeling of Sink Mark Formation in Cross-Rib-Reinforced Injection-Molded Plastic Parts by Localized Finite Element Shrinkage Analysis

Shi, L., Gupta, M.

Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Increased Speed to Market Using CAE Simulation for Injection Molded Plastics Parts

Duff, A. L.

Society of Plastics Engineers, Inc. (SPE)
9 国際会議録 A Procedure for the Design Optimization of Injection Molded Plastic Parts Using CAD/CAE Softwares (223)

Candal,M.V., Morales,R.A., Gonzalez,O.

Society of Plastic Engineers.
4 国際会議録 Sink Mark Study in Injection Molded Parts

Liou J. M., Ramachandra M. D., Ishii K., Hornberger L.

Society of Plastics Engineers, Inc. (SPE)
10 国際会議録 Using Computer Software Analysis with Gas Assist Injection Molded Parts

Hotchkiss, J. W.

Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Design of an Injection Mold with Removable Plates Using CAE

Villarroel, S., Morales, R. A., Rojas, H.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Using Compuer Software Analysis with Gas Assist Injection Molded Parts

Hotchkiss W. J.

Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 An Integrated Analysis of the Injection Molded Plastic Parts

Davidoff, A., Bung, H., Chen, S. C.

Society of Plastics Engineers, Inc. (SPE)
12 国際会議録 Off-Line Quality Analysis of Injection Molded Parts Using Experimental Design

Henza Don, Lipowicz Loretta

Society of Plastics Engineers, Inc. (SPE)
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12