Mold heating System Design

Mold heating System Design

著者名:

Kwon, T. ( The State University of New Jersey )
Forcucci, S.

掲載資料名:

ANTEC 88, Atlanta, April 18-21, 1988, Conference proceedings : plastics are shaping tomorrow today : Society of Plastics Engineers 46th annual technical conference & exhibits

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

34

発行年:

1988

開始ページ:

1585

終了ページ:

1587

総ページ数:

3

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/882018

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00020623
シリーズID:	PA00000030
会議名:	ANTEC '88 : Society of Plastics Engineers Annual Technical Conference and Exhibit
回次:	46th
会議開催地:	Atlanta, GA, USA
会議開催年:	1988.04.18-1988.04.21
論文注記:	DESIGN SPECIAL SESSION

類似資料:

1 国際会議録 Injection Molding Cooling System Design Opolski, S. W., Kwon, T. W. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Integral optical system design of injection molded optics Baeumer, S.M., Shulepova, L., Willemse, J., Renkema, K. SPIE-The International Society for Optical Engineering
2 国際会議録 Mechanical Properties Depending on Fiber Orientation in Injection Molded Short-Fiber-Reinforced Plastic Parts Chung, S., Kwon, T. American Institute of Chemical Engineers	8 国際会議録 Integration of CAD/CAM/CAE in Mold Design and Manufacturing Tseng, H. H., Lai, F. S., Peng, T. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Effect of the design and the tolerance parameters on the thermosonic transverse bonding flip chip system H. K. Jung, W. T. Kwon, S.-I. Lee Society of Photo-optical Instrumentation Engineers	9 国際会議録 Time-discretization of nonlinear system with time delayed output via taylor series [6042-50] Zhang Y., Kwon O. S, Chong K. T SPIE - The International Society of Optical Engineering
4 国際会議録 Unified Design Method of the Cavity for Injection Molded Spur Gears Lee, S. -C., Kim, C. -H., Kwon, O. -K., Huh, Y. -J. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 An Intelligent Fucntion-Based Design System for Injection Molded Plastic Parts Manoochehri, S. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Development of a rational design procedure for a pressure recovery system for HPCL Kim, S., Jin, J., Kwon, H., Kwon, S. SPIE - The International Society of Optical Engineering	11 国際会議録 An Integrated System Approach for Injection Molded Plastic Parts from Design to Fabrication Nagarsheth S. P. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Computer-Aided Cooling-system Design for Injection Molding Kwon H. T., Wang K. K. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Design of a quadrocopter simulator with 5-DOF [6042-38] Min H. G, Jeung E. T, Kwon S. -H SPIE - The International Society of Optical Engineering

1

2

3

4

5

6

7

8

9

10

11

12