In-Line Pressure and Infrared Temperature Measurements for Injection Moulding Process Control

In-Line Pressure and Infrared Temperature Measurements for Injection Moulding Process Control

著者名:

Speight G. R. ( University of Bradford )
Coates D. P. ( University of Bradford )
Yazbak P. E. ( Dynisco Instruments, Inc. )

掲載資料名:

ANTEC 95, Boston, May 7-11, Boston : The plastics challenge - a revolution in education : Volume I. Processing

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

41(1)

発行年:

1995

巻:

1

開始ページ:

647

終了ページ:

651

総ページ数:

5

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566763196 [1566763193]

言語:

英語

請求記号:

S42700/962601

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00020153
シリーズID:	PA00000030
会議名:	ANTEC '95 :: Annual Technical Conference
回次:	53rd
会議開催地:	Boston, MA, USA
会議開催年:	1995.05.07-1995.05.11
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 In-line process measurements for integrated injection molding Speight, R.G., Yazbak, E.P., Coates, P.D. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Injection Molding Process Control Speight, R. G., Thomas, A. R. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Pressure Measurements for Injection Moulding Control Speight G. R., Hull B. J. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Automated Set-Up for Gas Assisted Injection Moulding (470) Mulvaney-Johnson,L., Coates,P.D., Speight,R.G. Society of Plastic Engineers.
3 国際会議録 The Use of Process Measurements for Real Time Injection Moulding Process Control Speight, R. G., Coates, P. D., Hull, J. B. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Closed-Loop Process Control Strategies for Thermoplastic Injection Molding Machines Bakharev, A., Brincat, P., Speight, R. Society of Plastics Engineers
4 国際会議録 Melt and Mould Temperature Measurements for Polymer Injection Moulding Speight G. R., D'Agostino P., Herrmann S. J. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Control of polymer melt flow front position during the injection molding process Speight, R.G., Hull, J.B., Coates, P.D. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 On-Line Viscosity Control for the Injection Molding Process Sherbelis, G., Speight, R. G. Society of Plastics Engineers	11 国際会議録 Closed-Loop Viscosity Control For Injection Molding (563) Bakharev,A.S., Speight,R.G., Brincat,P.A. Society of Plastic Engineers.
6 国際会議録 Setup and Optimisation of the Gas Assisted Injection Moulding Process Using an Expert System Coates, P.D., Mulvaney-Johnson, L., Speight, R.G., Brincat P., Bakharev, A.S. Society of Plastics Engineers	12 国際会議録 Comparison of Injection Moulding Simulation and In-Process Measurements Leman Z., Coates D. P. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12