Polymer Flow Length Simulation During Injection Mold Filling

Polymer Flow Length Simulation During Injection Mold Filling

著者名:

Buchmann M. ( University of Wisconsin-Madison )
Theriault P. R.
Osswald A. T.

掲載資料名:

ANTEC 95, Boston, May 7-11, Boston : The plastics challenge - a revolution in education : Volume I. Processing

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

41(1)

発行年:

1995

巻:

1

開始ページ:

546

終了ページ:

550

総ページ数:

5

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566763196 [1566763193]

言語:

英語

請求記号:

S42700/962601

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00020153
シリーズID:	PA00000030
会議名:	ANTEC '95 :: Annual Technical Conference
回次:	53rd
会議開催地:	Boston, MA, USA
会議開催年:	1995.05.07-1995.05.11
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 Modeling and Simulation of High Reynolds' Number Flows During Reaction Injection Mold Filling Spiegelhoff J. T., Osswald A. T. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Flow Front Behavior During Co-Injection Mold Filling K. T. Nguyen, A. Derdouri, D. M. Gao, K. A. Koppi American Society of Mechanical Engineers
2 国際会議録 Properties of Thermosetting Polymers during Cure Theriault R., Osswald A. T., Stradins L. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Determining Etch Compensation Factors for Printed Circuit Boards DeRose, A., Theriault, R. P., Osswald, T. A., Castro, J. M. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Residual Stress Development during Laminate Processing Theriault P. R., Osswald A. T., Castro M. J. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Novel BEM Simulation of Mixing in polymer Flows Including Non-Linear Effects Rios, A. C., Osswald, T. A. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 3-D Curing Simulation of Thick Thermoset Components Viego, J., Theriault, R. P., Osswald, T. A. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 An Automated simulation of Compression Mold Filling for Complex Parts Osswald, Tim A., Tucker, Charles L III Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Computer Simulation of Injection Mold Filling for Viscoelastic Melts with Fountain Flow Kamal, M. R., Chu, E., Lafleur, P. G., Ryan, M. E. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Excess Pressure Drops around Corners during Injection Mold Filling Process Hingorani, A., Patel, T., Randall, C., McCarthy, S. P. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Simulating the Flow and Heat Transfer Effects During Polymer Processing Using the Boundary Element Method Gramann P., Osswald T. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Investigation of non-linear effects of polymer flows during mixing Davis, Bruce A., Osswald, T.A. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12