Case Studies of the Gas-Assisted Injection Molded Parts Designed with a Gas Channel of Different Geometry

Case Studies of the Gas-Assisted Injection Molded Parts Designed with a Gas Channel of Different Geometry

著者名:

Chen C. S. ( Chung Yuan University )
Hsu S. K. ( Chung Yuan University )
Liu L. W. ( Materials Research Laboratories of ITRI )
Chen C. Y. ( Materials Research Laboratories of ITRI )
Ho K. K. ( Materials Research Laboratories of ITRI )

掲載資料名:

ANTEC 95, Boston, May 7-11, Boston : The plastics challenge - a revolution in education : Volume I. Processing

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

41(1)

発行年:

1995

巻:

1

開始ページ:

530

終了ページ:

533

総ページ数:

4

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566763196 [1566763193]

言語:

英語

請求記号:

S42700/962601

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00020153
シリーズID:	PA00000030
会議名:	ANTEC '95 :: Annual Technical Conference
回次:	53rd
会議開催地:	Boston, MA, USA
会議開催年:	1995.05.07-1995.05.11
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 A Study of the Weldline Strength in Gas-Assist Injection Molded Thermoplastics Liu, S. -J., Ho, C. -Y., Chang, J. -H. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 A Novel Computer Simulation Technology for the Cooling Analysis of Complex Injection Molded Parts Chang, R. -Y., Huang, S. -H., Yang, W. -L., Chen, I. Y., Lai, C. C. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Numerical Simulations and Experimental Studies of Gas-Assisted Injection Molding Chen, S. C., Hsu, K. S., Jeng, M. C. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Computer-Aided Gas-Assisted Injection-Molding of the front Cover of Motorcycle Headlight Chang -Y. R., Lin -C. S., Chen -C. K., Hsu -H. C., Tsai -H. M. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Structure Performance of Thin-Wall Injection Molded Parts Chen, S. C., Jong, W. R., Chang, Y. P., Kang, Y., Peng, H. S., Huang, L. T., Ynag, L. K., Chang, C. T., Luo, R. C. Society of Plastics Engineers	9 国際会議録 Experimental Investigation of the Warpages in Rotationally Molded Parts Liu -J. S., Ho -Y. C. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Structural Analysis, process Si,ulation and Warpage Calculation for the Gas-Assisted Injection Molded Parts Using a Unified CAE Model Chen C. S., Hu Y. S., Jong R. W., Jeng C. M. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Post-Filling Simulation and Analyses of Shrinkage and Warpage of the Injection Molded Parts Chen, S. -C., Jeng, K. -K. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Plasma assisted MBE growth and characterizations of GaN Tu, L.-W., Lee, K.-H., Lai, C.-M., Hsu, M.-K., Chen, W.-S., Liu, C.-S., Lo, I., Tsai, J.-K., Ho, P.-C., Hsieh, K.-Y., … SPIE-The International Society for Optical Engineering	11 国際会議録 Optimum Design of Process Conditions to Minimize Residual Stresses in Injection-Molded Parts Kang S., Hieber A. C., Wang K. K. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Effect of gas channel design on molding window and part mechanical properties of gas-assisted injection molding Chen, S.C., Dong, J.G., Jong, W.R., Huang, J.S., Jeng, M.C. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Using Computer Software Analysis with Gas Assist Injection Molded Parts Hotchkiss, J. W. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12