Blank Cover Image

Computer Aided Design of Preforms for Injection Stretch Blow Moulding

著者名:
掲載資料名:
ANTEC '99 Conference proceedings, New York City, May 2-6, 1999 : plastics bridging the millennia
シリーズ名:
Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers
シリーズ巻号:
45(1)
発行年:
1999
巻:
1
開始ページ:
988
終了ページ:
992
総ページ数:
5
出版情報:
Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)
ISBN:
9781566768047 [1566768047]
言語:
英語
請求記号:
S42700/45-1
資料種別:
国際会議録

類似資料:

1 国際会議録 A Web Based Stretch Blow Moulding Simulation (958)

Kwok,P.S., Menary,G.H., Armstrong,C.G.

Society of Plastic Engineers.
7 国際会議録 Three-Dimensional Computer-Aided Mold Cooling Design for Injection Molding

Chang, R.Y., Hsu, D.C., Yang, V., Yang, W.H.

Society of Plastics Engineers
2 国際会議録 Injection/Stretch Blow Moulding of PET/LCP Blends for Better Product Performance

Garcia-Rejon, A., Nguyen, K. T., Michaeli, W., Morich, L., Schmidt, G., Lusignea, R.

Society of Plastics Engineers, Inc. (SPE)
8 国際会議録 An Analysis of Heating Efficiency in Rotational Moulding

Wright J. M., Spence G. A., Crawford J. R.

Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Injection/Stretch Blow Moulding of Polymer/Clay Nanocomposites

Garcia-Rejon, A., Simard, Y., DeGrandpre, C.

Society of Plastics Engineers
9 国際会議録 The Temperature Dependent Viscoelastic and Viscoplastic Properties of Nylon 12

McFerran, N.A., Armstrong, C., McNally, T., Menary, G., McNally, G.

Society of Plastics Engineers
4 国際会議録 The Influence of Different Processing Parameters on the Properties of Polypropylene for Rotational Moulding

Van Hooijdonk, J. P. F., Kearns, M. P., Armstrong, C. G., McCann, B., Coey, L., Crawford, R. J.

Society of Plastics Engineers
10 国際会議録 Recycling of Polyolefins in Blow Moulding

DiRaddo, R. W., Pecora, L., Garcia-Rejon, A., Inch, J. I.

Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Computer Simulation of the Rotational Moulding of Plastics

Wright, E. J., Crawford, R. J.

Society of Plastics Engineers, Inc. (SPE)
11 国際会議録 Recycling of Polyolefins Blow Moulding

DiRaddo, R. W., Pecora, L., Garcia-Rejon, A., Inch, J. I.

Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Computer Modelling of th Roatational Moulding Process

Attaran T. M., Wright J. E., Crawford J. R.

Society of Plastics Engineers, Inc. (SPE)
12 国際会議録 Computer Aided Engineering Design of Powder Injection Molding Process for a Dental Scaler Tip Mold Design

C.J. Hwang, Y.B. Ko, H.P. Park, S.T. Chung, B.O. Rhee

Trans Tech Publications
1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12