Optimization of the injection molding process

Optimization of the injection molding process

著者名:

Dillman, S.H. ( Western Washington University )
Howe, D.
Robar, H.

掲載資料名:

ANTEC '96 : Plastics-Racing into the Future, May 5-10, Indianapolis : conference proceedings

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

42

発行年:

1996

巻:

Vol. 1

開始ページ:

754

終了ページ:

758

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/970361

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018810
シリーズID:	PA00000030
会議名:	ANTEC '96
回次:	54th
会議開催地:	Indianapolis, IN, USA
会議開催年:	1996.05.05-1996.05.10

類似資料:

1 国際会議録 The Effect of Nitrogen Purging on Degradation During Reprocessing in Injection Molding Archer, J.S., Dillman, S.H. Society of Plastics Engineers	7 国際会議録 Microcelluar Nnocomposite Injection Molding Process Yuan, M., Turng, L-S.T., Spindler, R., Caulfield, D.F., Hunt, C. Society of Plastics Engineers
2 国際会議録 A "Six Sigma" Approach to Process Optimization for the Rotational Molding Industry: Phase I Ibeb, C.C., Wonderly, E., Afonja, S., Rhodes, E.H., Howe, E. Society of Plastics Engineers	8 国際会議録 Thin-Wall Injection Molding Chen, S. C., Peng, H. S., Huang, L. T., Chang, C. T., Wei, D. Y., Ruo, R. C. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Optimization Strategies for Injection Molding Turng S. L., Chiang H. H., Stevenson F. J. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Optimization of Perform for Blow Molding Process Lee K. D., Soh K. S. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Optimization of Injection-Molding Process with Genetic Algorithms Ye, H., Wang, K. K. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Application of Optimization Algorithms in Injection Molding Process Parameters Optimization Z.H. Hu, W. Wei, J. Liu, K. Liu Trans Tech Publications
5 国際会議録 Optimization of Process Conditions in Gas-Assisted Injection Molding Chen, M., Yao, D., Kim, B. Society of Plastics Engineers	11 国際会議録 Investigation of Optimum Conditions of Thin-Wall Injection Molding Process (872) Liao,S.J., Chang,D.Y., Chen,H.J., Tsou,L.S., Ho,J.R., Yau,H.T., Hsieh,W.H., Wang,J.T., Su,Y.C. Society of Plastic Engineers.
6 国際会議録 Recycled Fiberglass Composite as a Reinforcing Filler in Post-Consumer Recycled HDPE Plastic Lumber George, S. D., Dillman, S. H. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Powder Injection Molding of Ti6Al4V Alloy X.H. Qu, S.B. Guo, C.F. Tang, M.L. Qin, X.B. He, S.H. Islam Trans Tech Publications

1

2

3

4

5

6

7

8

9

10

11

12