An experimental study to investigate the influene of processing conditions in the gas-assisted injection molding process

An experimental study to investigate the influene of processing conditions in the gas-assisted injection molding process

著者名:

掲載資料名:

ANTEC '96 : Plastics-Racing into the Future, May 5-10, Indianapolis : conference proceedings

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

42

発行年:

1996

巻:

Vol. 1

開始ページ:

649

終了ページ:

654

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/970361

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018810
シリーズID:	PA00000030
会議名:	ANTEC '96
回次:	54th
会議開催地:	Indianapolis, IN, USA
会議開催年:	1996.05.05-1996.05.10

類似資料:

1 国際会議録 A High Pressure Gas Proportional Controller for Gas-Assisted Injection Molding Lasch E., Csongor D., Kapila V., Schott R. N. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Automotive door hardware module by gas injection molding Shah, Suresh, Juback, Glen, Sajan, Anthony, Clark, Chris Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Experimental Studies in Gas-Assist Injection Molding to Investigate Residual Wall Thickness and Gloss Levels (1115) Cooper,C., Kampian,J., McCanna,J., Protte,R. Society of Plastic Engineers.	8 国際会議録 On the Dynamics of Gas-Assisted Injection Molding Process Chang -Y. R., Tsai -H. M., Hsu -H. C. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Experimental studies of design guidelines for gas-assisted injection molding process Jong, Wen-Ren, Huang, Jeng-Sheng, Chang, Yung-Shin Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Effects of gate design on the processing latitudes of engineering thermoplastics Shah, Dhruv J., Schott, Nick R., Rahman, M. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Optimization of Process Conditions in Gas-Assisted Injection Molding Chen, M., Yao, D., Kim, B. Society of Plastics Engineers	10 国際会議録 Experimental Case Studies of Dimensional Repeatability on Gas Assisted Injection Molding Process and Cavity Pressure Controlled Closed Loop Injection Molding … Okeke E., Cosma L. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Experimental Study of Gas-Assisted Injection Molding Yang, S. Y., Liou, S. J. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Experimental Study of Gas Penetration in the Gas-Assisted Injection Molding (174) Shin,J-W., Isayev,A.I. Society of Plastic Engineers.
6 国際会議録 Processing Strategies for Thin Wall Injection Molding Tantakom P., Schott R. N. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Gas-assisted injection molding: influence of processing conditions and material properties Koelling, Kurt W., Kaminski, Ronald Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12