Visual Analyses of Flow Marks Generation Process Using Glass-Inserted Mold-Part II. Synchronous Flow Marks with Same Phases on Both Top and Bottom Surfaces of Molded Samples

Visual Analyses of Flow Marks Generation Process Using Glass-Inserted Mold-Part II. Synchronous Flow Marks with Same Phases on Both Top and Bottom Surfaces of Molded Samples

著者名:

Yokoi, H. ( University of Tokyo )
Murata, Y. ( Sekisui Chemical Co., Ltd. )
Deguchi, Y. ( Sumitomo Heavy Industries, Ltd. )
Sakamoto, I.

掲載資料名:

ANTEC 94 : plastics : gateway to the future : conference proceedings, San Francisco May 1-5 1994 : Volume I. Processing

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

40(1)

発行年:

1994

巻:

1

開始ページ:

829

終了ページ:

832

総ページ数:

4

出版情報:

Brookfield, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/941468

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00018760
シリーズID:	PA00000030
会議名:	ANTEC '94 : Annual Technical Conference
回次:	52nd
会議開催地:	San Francisco, CA, USA
会議開催年:	1994.05.01-1994.05.05
論文注記:	INJECTION MOLDING DIVISION

類似資料:

1 国際会議録 Visual Analyses of Flow Marks Generation Process Using Glass-Inserted Mold-Part I. Micro-Grooved Flow Marks Yokoi, H., Murata, Y., Nagami, S., Kawasaki, A. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Visual Observation of Three-Dimensional Melt Flow Inside a Mold Cavity by Gate-Magnetization Method Yokoi, H., Kanematsu, T. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Visual Analysis of Fiber Orientation Process by Glass-Inserted Mold. Part II: Analysis Using a Fiber Tracing Method Yokoi, H., Murata, Y., Nagaya, N., Harada, H. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Blow Molding Engineering Thermoplastics Method of Improving the Molded Part Surface Part II: Heat/Cool Process Cycle Time Study Ferguson L., Takatori H., Furuya H. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Visual Analysis of Fiber Orientation Process by Glass-Inserted Mold. Part 1: Analysis Using a Back-Lighting Method Yokoi, H., Murata, Y., Nishi, Y., Seki, T. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Measurement of Shear Stress Distributions on a Mold Cavity Wall during the Filling Process Yokoi, H., Masuda, N., Kosaki, R. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Visual Analysis of Weld Line Vanishing Process by Glass-Inserted Mold Yokoi, H., Oka, K., Watanabe, H. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Dynamic Visualization of Cavity Filling Process along Thickness Direction Using a Laser-Light-Sheet Technique Yokoi, H., Inagaki, Y. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Direct Observation of jetting Phenomena under a High Injection Pressure by Using a Prismatic-Glass Inserted Mold Yokoi, H., Hayashi, T., Morikita, N., Toda, K. Society of Plastics Engineers, Inc. (SPE)	11 テクニカルペーパー Brake Pad Surface Topography Part II: Squeal Generation and Prevention. Bakar, A.R.A., Ouyang, H., Li, L., Siegel, J.E. Society of Automotive Engineers
6 国際会議録 Measurement of Melt Temperature Profiles during Filling and packing Processes Using a New Integrated Thermocouple Sensor Yokoi, H., Murata, Y., Tsukakoshi, H. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Americium/curium vitrification process development part II Fellinger, Andrew P., Baich, Mark A., Duvall, Jon W., Jones, Timothy M., Marra, John E., Miller, Carey B., Miller, … MRS-Materials Research Society

1

2

3

4

5

6

7

8

9

10

11

12