The Influence of Different Processing Parameters on the Properties of Polypropylene for Rotational Moulding

The Influence of Different Processing Parameters on the Properties of Polypropylene for Rotational Moulding

著者名:

Van Hooijdonk, J. P. F. ( The Queen's University of Belfast )

Kearns, M. P. ( Clarehill Plastics Limited )

Armstrong, C. G. ( The University of Auckland )

掲載資料名:

ANTEC 2001, conference proceedings, Dallas, Texas, May 6-10

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

47

発行年:

2001

パート:

1

開始ページ:

1326

終了ページ:

1330

総ページ数:

5

出版情報:

Brookfield Center, CT: Society of Plastics Engineers

ISBN:

9781587160981 [1587160986]

言語:

英語

請求記号:

S42700/47

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00017839
シリーズID:	PA00000030
会議名:	ANTEC 2001
回次:	2001
会議開催地:	Dallas, TX, USA
会議開催年:	2001.05.06-2001.05.10

類似資料:

1 国際会議録 A Comparison between Open Flame and Hot Air Heating Methods for the Rotational Moulding of Plastics Kearns, M. P., Corrigan, N., Crawford, R. J. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Effects of Cooling Rate on the Mechanical Properties of Rotationally Moulded Polyethylene Parts (127) Callan,N., Kearns,M.P., Crawford,R.J., Spencer,M. Society of Plastic Engineers.
2 国際会議録 The Effect of Direct Electrical Heating on the Cycle Time and Mechanical Properties of Rotationally Molded Polyethylene Parts Kearns, M.P., Daly, C., Crawford, R.J. Society of Plastics Engineers	8 国際会議録 Investigation of the Processing Characteristics and Mechanical Properties of Metallocene Polyethylene Foams for Rotational Moulding (26) Archer,E., Harkin-Jones,E., Kearns,M.P., Fatnes,A-M. Society of Plastic Engineers.
3 国際会議録 System Modelling for the Control of the Rotational Molding Process Abu Fara, D. I., Kearns, M. P., Crawford, R. J. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 The Influence of Processing Parameters on the Properties of Melt-Spun Polypropylene Hollow Fibers de Rovere, A., Grady, B. P., Shambaugh, R. L. Society of Plastics Engineers
4 国際会議録 Process Control for Rotational Moulding of Plastics Crawford J. R., Nugent J. P., Spence A. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Computer Aided Design of Preforms for Injection Stretch Blow Moulding Menary, G. H. Armstrong, C. G., Crawford, R. J. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 The Influence of Processing Parameters on the Mechanical Properties of Rotationally Moulded Reactive Nylon Harkin-Jones E., Crawford J. R. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Investigation of Rotational Moulding Characteristics and Mechanical Properties of Metallocene Polyethylene Wang, X., Harkin-Jones, E., Crawford, R. J., Fatnes, A. M. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 An Analysis of Heating Efficiency in Rotational Moulding Wright J. M., Spence G. A., Crawford J. R. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 SHELL MIDDLE DISTILLATE HYDROGENATION PROCESS Lucien, J. P., Berg, J. P. van den, Germaine, G., Hooijdonk, H. M. J. H. van, Gjers, M., Thielemans, G. L. B. American Institute of Chemical Engineers

1

2

3

4

5

6

7

8

9

10

11

12