Gas Assisted Injection Moulding: 3D Finite Element Modelling Using a pseudo concentration method and Experimental Studies

Gas Assisted Injection Moulding: 3D Finite Element Modelling Using a pseudo concentration method and Experimental Studies

著者名:

Johnson, L. ( University of Bradford )
Olley, P.
Coates, P. D.

掲載資料名:

ANTEC 2001, conference proceedings, Dallas, Texas, May 6-10

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

47

発行年:

2001

パート:

1

開始ページ:

764

終了ページ:

768

総ページ数:

5

出版情報:

Brookfield Center, CT: Society of Plastics Engineers

ISBN:

9781587160981 [1587160986]

言語:

英語

請求記号:

S42700/47

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00017839
シリーズID:	PA00000030
会議名:	ANTEC 2001
回次:	2001
会議開催地:	Dallas, TX, USA
会議開催年:	2001.05.06-2001.05.10

類似資料:

1 国際会議録 Ultrasonic Monitoring of Gas Assisted Injection Moulding (GAIM) Brown, E.C., Mulvaney-Johnson, L., Coates, P.D. Society of Plastics Engineers	7 国際会議録 Ultrasonic Investigation of Process Variation during Single Screw Extrusion and Injection Moulding: Reat Time Detection of Temperature Profile and Material … Brown, E. C., Olley, P., Collins, T. L. D., Coates, P. D. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Setup and Optimisation of the Gas Assisted Injection Moulding Process Using an Expert System Coates, P.D., Mulvaney-Johnson, L., Speight, R.G., Brincat P., Bakharev, A.S. Society of Plastics Engineers	8 国際会議録 Optimization of gas assisted injection moulding by using multiple gas injection systems Gao, D.M., Nguyen, K.T., Garcia-Rejon, A., Salloum, G. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Automated Set-Up for Gas Assisted Injection Moulding (470) Mulvaney-Johnson,L., Coates,P.D., Speight,R.G. Society of Plastic Engineers.	9 国際会議録 Optimising Gas-Assisted Injection Moulding Process Using the Taguchi Method Zhao, J., Ge, C., Ravi, V. Trans Tech Publications
4 国際会議録 3D Finite Element Method for the Simulation of the Filling Stage in Injection Moulding Hetu, J., Gao, D., Garcia-Rejon, A., Salloum, G. American Institute of Chemical Engineers	10 国際会議録 On the Comparison of the Pseudo Rigid Body Model Method and the Finite Element Method for a 3DOF Planar Micro-Motion Stage J. Zou, L. G. Watson, W. J. Zhang American Society of Mechanical Engineers
5 国際会議録 3D finite element method for the simulation of the filling stage in injection moulding Hetu, J.F., Gao, D.M., Garcia-Rejon, A., Salloum, G. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Thoretical and Experimental Study of the Injection Moulding of High Performance Thermoplastic Composites Garcia-Rejon A., Salloum G., Hebert P. L. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Fluid Assisted Polymer Processing in Extrusion and Injection Moulding: A Comparative Overview Mulvaney-Johnson, L., Woodhead, M., Rose, M., Dawson, A., Gough, T.D., Coates, P.D., Smith, G.F., Goodship, V., … Society of Plastics Engineers	12 国際会議録 Reduction of Injection Moulded Plastic Part Warpage Using Advanced Gas Assisted Injection Moulding M. Košęk, J. Bílik, D.R. Delgado Sobrino Trans Tech Publications

1

2

3

4

5

6

7

8

9

10

11

12