Study of Flow Marks during Thin-Wall Injection Molding

Study of Flow Marks during Thin-Wall Injection Molding

著者名:

Xu, G. ( The Ohio State University )
Koelling, K. W.

掲載資料名:

ANTEC 2001, conference proceedings, Dallas, Texas, May 6-10

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

47

発行年:

2001

パート:

1

開始ページ:

604

終了ページ:

607

総ページ数:

4

出版情報:

Brookfield Center, CT: Society of Plastics Engineers

ISBN:

9781587160981 [1587160986]

言語:

英語

請求記号:

S42700/47

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00017839
シリーズID:	PA00000030
会議名:	ANTEC 2001
回次:	2001
会議開催地:	Dallas, TX, USA
会議開催年:	2001.05.06-2001.05.10

類似資料:

1 国際会議録 Study of Flow Marks during Injection Molding (269) Xu,G., Koelling,K.W. Society of Plastic Engineers.	7 国際会議録 171e. Flow Dynamics in Injection Molding with Microfeatures Goujun Xu, Xin Hu, Kurt W. Koelling, L. James Lee American Institute of Chemical Engineers
2 国際会議録 Study of Cavity Pressure and its Prediction During Injection Molding Xu, G., Koelling, K.W. Society of Plastics Engineers	8 国際会議録 Predicting Thermal Degradation of PVC Compounds during Injection Molding Garcia, J. L., Koelling, K. W., Summers, J. W. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Computational Prediction of PVC Degradation during Injection Molding Radial Flow Yu, L., Garcia, J., Xu, G., Koelling, K.W., Summers, J.W. Society of Plastics Engineers	9 国際会議録 Eliminating PVC Degradation during Injection Molding Using Computational Techniques Garcia, J. L., Koelling, K. W., Summers, J. W. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Flow and Heat Transfer Simulation of Thin-Wall Injection Molding with Microstructures Yu, L., Lee, L.J, Koelling, K.W. Society of Plastics Engineers	10 国際会議録 The Influence of Polymer Rheology on Bubble Penetration in Gas-Assisted Injection Molding Gauri, V., Koelling, K. W. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Thin Wall Injection Molding of Thermoplastic Microstructures Yu, L., Juang, Y. -J., Koelling, K. W., Lee, L. J. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Numerical Simulation of PVC Degradation During Injection Molding Koelling, Kurt W., Summers, James W., Garcia, Jose L. American Institute of Chemical Engineers
6 国際会議録 Experimental and Numerical Analysis of Thin-Wall Injection Molding with Micro-Features Yu, L., Koh, C. G., Koelling, K. W., Lee, L. J., Madou, M. J. Society of Plastics Engineers	12 国際会議録 Study of Polymer Melt Flow during Injection Molding Using Co-Injection Molding Technique Chen, S. C., Hsu, K. F., Jung, W. R. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12