Incorporating Dimensional Requirements into Material Selection and Design of Injection Molded Parts

Incorporating Dimensional Requirements into Material Selection and Design of Injection Molded Parts

著者名:

Beiter A. K. ( Stanford University )
Ishii K. ( Stanford University )

掲載資料名:

ANTEC '97 : plastics saving planet earth, Society of Plastics Engineers, April 27-May 2 : conference proceedings

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

43

発行年:

1997

パート:

3

開始ページ:

3295

終了ページ:

3299

総ページ数:

5

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

ISBN:

9781566765534 [1566765536]

言語:

英語

請求記号:

S42700/43-1

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00016900
シリーズID:	PA00000030
会議名:	ANTEC '97 : Annual Technical Conference
回次:	55th
会議開催地:	Indianapolis, IN, USA
会議開催年:	1997.04.27-1997.05.02
論文注記:	ANTEC '97, 55th Annual Technical Conference, April 27-May 2, 1997, Indianapolis, USA

類似資料:

1 国際会議録 Weld-Line Strength in Injection Molded PVC Parts Merhar, C. F., Beiter, K. A., Ishii, K. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 Performance Characterization of Recycled Thermoplastics for Material Life-Cycle Analysis Shriver, M. E., Beiter, K. A., Ishii, K. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Incorporating the Voice of the Customer in Preliminary Component Design Kurt A. Beiter, Kosuke Ishii American Society of Mechanical Engineers	8 国際会議録 Control of Dimensional Variability in Injection Molded Plastic Parts Xia Z., Mallick K. P. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 Preliminary plastic part design: focus on material selection & basic geometry while balancing mechanical performance & manufacturing cost Beiter, Kurt A., Cardinal, James M., Ishii, Kosuke Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Investigation of Material, Process, and Design Effects on Color and Appearance of Injection Molded Aircraft Parts Griffing S. J., Whitaker M. K. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Customer Requirements Management: Methodology Selection and Deployment Guide Kurt A. Beiter, Kosuke Ishii, Harshavardhan Karandikar American Society of Mechanical Engineers	10 国際会議録 Mold-Filling-Simulation in Injection Molding of Three-Dimensional Thin Parts Wang W. V., Hieber A. C., Wang K. K. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Sink Mark Study in Injection Molded Parts Liou J. M., Ramachandra M. D., Ishii K., Hornberger L. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Optimum Design of Process Conditions to Minimize Residual Stresses in Injection-Molded Parts Kang S., Hieber A. C., Wang K. K. Society of Plastics Engineers, Inc. (SPE)
6 国際会議録 Advanced Design Guidelines to Assess Fillability Mehl D. C., Beiter K. A., Ishii K. Society of Plastics Engineers, Inc. (SPE)	12 国際会議録 Automatic Design Optimization Molding Simulation for Injection Molded Parts Barton, K. S., Lin, B., Ryim, W. G. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12