Design and Development of Injection Molded FRP Crank Chain Wheel Assebmly for a Bicycle

Design and Development of Injection Molded FRP Crank Chain Wheel Assebmly for a Bicycle

著者名:

Gupta, A. ( Indian Institute of Technology )
Misra, A.
Mittal, R. K.
Rao, P. N.

掲載資料名:

Back to the future : conference proceedings : ANTEC 1992, Detroit, May 3-7

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

38

発行年:

1992

パート:

2

開始ページ:

2424

終了ページ:

2426

総ページ数:

3

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/921583

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00017837
シリーズID:	PA00000030
会議名:	ANTEC 1992 : Annual Technical Conference
回次:	50th
会議開催地:	Detroit, MI, USA
会議開催年:	1992.05.03-1992.05.07
論文注記:	DESIGN SPECIAL INTEREST GROUP
書誌注記:	目次はDivisionごとに分けて掲載されている。論文の順番はDivisionにかかわらず，Session順の通しページになっている。

類似資料:

1 国際会議録 (329d) The Influence of Processing Parameters and Use of a Chain Extender on the Mechanical and Thermal Properties of Injection Molded Poly (trimethylene … Petri Myllytie, Manju Misra, Amar K. Mohanty American Institute of Chemical Engineers	7 国際会議録 Injection Molded Biocomposites from Natural Fibers and Modified Polyamide Misra, M., Mohanty, A.K., Drzal, L.T., Tummala, P. Society of Plastics Engineers
2 国際会議録 (329d) The Influence of Processing Parameters and Use of a Chain Extender on the Mechanical and Thermal Properties of Injection Molded Poly (trimethylene … Petri Myllytie, Manju Misra, Amar K. Mohanty American Institute of Chemical Engineers	8 国際会議録 Injection molded microfluidic devices for biological sample separation and detection (Invited Paper) [6109-01] Morales, A. M., Simmons, B. A., Wallow, T. I., Campbell, K. J., Mani, S. S., Mittal, B., Crocker, R. W., Cummings, E. … SPIE - The International Society of Optical Engineering
3 国際会議録 (329d) The Influence of Processing Parameters and Use of a Chain Extender on the Mechanical and Thermal Properties of Injection Molded Poly (trimethylene … Petri Myllytie, Manju Misra, Amar K. Mohanty American Institute of Chemical Engineers	9 国際会議録 Methodial Designing of Molds for Injection Molding of Polymers Raos P., Catic I. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Optimization of Cooling System in Injection Molds by an Easily Applicable Analytical Model Rao, N. S., Schumacher, G., Schott, N. R., O'Brien, K. T. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Design of Pin Ejector Systems for Injection Molds Malloy R., Majeski P. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Predicting Warpage of Injection Molded Fiber-Reinforced Plastics Zheng R., McCaffrey N., Winch K., Yu H., Kennedy P. Society of Plastics Engineers, Inc. (SPE)	11 国際会議録 Practical Relationships for Calculating Pressure Drop in Injection Molds (41) Rao,N.S., Schumacher,G., Schott,N.R., Edwards,R. Society of Plastic Engineers.
6 国際会議録 A General Method of Designing Injection Molds by Straightforward Solution Procedures Rao, N.S., Schumacher, G., Schott, N.R. Society of Plastics Engineers	12 国際会議録 Automated Injection Mold Getting Design System Irani K. R., Kim H. B., Dixon R. J. Society of Plastics Engineers, Inc. (SPE)

1

2

3

4

5

6

7

8

9

10

11

12