Integrated Analysis of the Injection Blow Molding Process

Integrated Analysis of the Injection Blow Molding Process

著者名:

Ryan E. M. ( State University of New York at Buffalo )
Haessly P. W. ( Industrial Materials Research Institute )
Garcia-Rejon A.

掲載資料名:

Plastics in the environment: yesterdy, today & tomorrow : conference proceedings : ANTEC 90, May 7-11, Dallas

シリーズ名:

Annual Technical Conference - ANTEC : Society of Plastics Engineers Annual Technical Papers

シリーズ巻号:

36

発行年:

1990

開始ページ:

754

終了ページ:

757

総ページ数:

4

出版情報:

Brookfield Center, CT: Society of Plastics Engineers, Inc. (SPE)

言語:

英語

請求記号:

S42700/902415

資料種別:

国際会議録

詳細

TDL書誌ID:	ZA00016899
シリーズID:	PA00000030
会議名:	ANTEC '90 : Annual Technical Conference
回次:	48th
会議開催地:	Dallas, TX, USA
会議開催年:	1990.05.07-1990.05.11
論文注記:	BLOW MOLDING DIVISION

類似資料:

1 国際会議録 Finite Element Modeling of the Injection Blow Molding Process Haessly P. W., Ryan E. M. Society of Plastics Engineers, Inc. (SPE)	7 国際会議録 On-Line Measurement of the Thickness of Blow Molding Parisons Garcia-Rejon A., Cielo P., Kamal R. M., Swan L. P. Society of Plastics Engineers, Inc. (SPE)
2 国際会議録 Effect of Initial Modulus Distribution on the Final Thickness of a Blown Preform Garcia-Rejon, A., Khayat, R., Ryan, M. E., Haessly, W. P. Society of Plastics Engineers, Inc. (SPE)	8 国際会議録 Relationship Between Mold Geometry, Processing Conditions and Mechanical Properties: Computer Integrated Injection Molding Application Salloum, G., LaGue, G., Garcia-Rejon, A. Society of Plastics Engineers, Inc. (SPE)
3 国際会議録 material Characterization Relevant to the Numerical Simulation of Blow Molding and Thermoforming Ryan, M. E., Garcia-Rejon, A. Society of Plastics Engineers, Inc. (SPE)	9 国際会議録 Numerical Simulation and Experimental Techniques Applied to Extrusion Blow Molding Garcia-Rejon A., DiRaddo W. R. Society of Plastics Engineers, Inc. (SPE)
4 国際会議録 Neural Network Modelling of the Injection Stage in Blow Molding DiRaddo W. R., Garcia-Rejon A. Society of Plastics Engineers, Inc. (SPE)	10 国際会議録 Heat Transfer Measurement at the Mold Surface During Injection Molding of Thermoplastic Melts Kamal, M. R., Salloum, G., Garcia-Rejon, A. Society of Plastics Engineers, Inc. (SPE)
5 国際会議録 Application of thermographic temperature measurements in injection molding and blow molding of plastics Prystay,M., Wang,H., Garcia-Rejon,A. SPIE-The International Society for Optical Engineering	11 国際会議録 Injection/Stretch Blow Moulding of Polymer/Clay Nanocomposites Garcia-Rejon, A., Simard, Y., DeGrandpre, C. Society of Plastics Engineers
6 国際会議録 The Influence of Operating Conditions on the Cooling Phase of the Extrusion Blow Molding Process (287) Kipping,A., Garcia-Rejon,A., Bendada,A. Society of Plastic Engineers.	12 国際会議録 Large Part Blow Molding (LPBM) of HDPE Resins: Parison Extrusion Behavior and Its Relathionship with the Resins' Rheologial Parameters Jivraj, N., Sehanobish, K., Ramanathan, R., Garcia-Rejon, A., Carmel, M. Society of Plastics Engineers

1

2

3

4

5

6

7

8

9

10

11

12